For Probs. 16.10 through 16.14, use comparator LM111 and vs = 10 sin (20007t) to plot the hysteresischaracteristic using PSpice/SPICE.16.11 The parameters of the Schmitt trigger in Fig. 16.25(a) are R₁ = 100 2 and RF = 47 k. Calculate theP threshold voltages +Vth and -Vth. Assume Vsat = |- Vsat = 12 V.RFVSR₁RxV₁+VdV_+A+

We need to find out the threshold voltage for given Schmitt trigger circuit.

16.11 The parameters of the Schmitt trigger in Fig. 16.25(a) are R₁ = 100 N and RF = 47 k. Calculate the = threshold voltages +Vth and -Vth- Assume V sat P -Vsat = = 12 V. RE R₁ Rx + Vd V_ + A + Vo

16.11 The parameters of the Schmitt trigger in Fig. 16.25(a) are R₁ = 100 N and RF = 47 k. Calculate the = threshold voltages +Vth and -Vth- Assume V sat P -Vsat = = 12 V. RE R₁ Rx + Vd V_ + A + Vo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2: Assume a sinusoidal signal with a frequency of 3.5 kHz and maximum amplitude of 1v. Then this signal is applied to LDM with a bit rate of 25kbps. Find the appropriate value of step size for this modulation.
ASAP It is a type of diode where it operates as a variable resistor when heated. Your answer What is the modulation index in ideal condition of AM. Your answer A form of AM where a sideband is filtered after its carrier is eliminated. Your answer What is the form of AM that used to transmit video signals of the TV system? Your answer It is a circuit in the superheterodyne receiver that adds and subtracts the frequencies of the AM signal and the local oscillator frequency. It is the extent to which the amplitude of the carrier wave is varied by modulating wave.
A receiver is being tested to determine SIINAD. A 400-Hz audio signal modulates a carrier that is applied to the receiver. Under these conditions, the output power is 7 mW. Next a filter is used to cancel the 400-Hz portion of the output, and then an output power of 0.18 mW is measured. Calculate SINAD. Cevap: Sonraki sayfa ar Geçiş yap.. on sy...pdf W
Determine the magnitude of gm for a JFET with Ipss =12 mA and Vp = -7 Vat the following de bias points with the graphical determination a. VGs = -1.5 V. b. VGs = -2.5 V. c. VGs = -3.5 v. %3D %3D This only d. Find the maximum value of gm- e. Find the value of gm at each operating point of (a. , b. , and c.) with the mathematical determination
DIGITAL COMMUNICATIONS H.W. Q1/ A) Find the sampling frequency for the following signals: 1) S1 = 20 cos(1500nt) * cos (4000nt) 2) S2 = sin (200xt. 3) S3 = sin4000nt + 5 cos(1200nt) nt B) The following waveform is the RB (return to bios) representation of the serial digital data, find the digital data code and draw the NRZ (non-return to zero) and RZ (return to zero) waveforms. C) waveform below is the PAM for the analog signal, draw the analog signal, PWM and the PPM for this signal. 02/ The following data stream (10011011 11001110 11110000 10001000 11100000 11011010 11111111 01110111 10011001 11100111 01011010) will be transmitted with signaling rate equal to 80 k bit/sec. 1- Find the data transmitted using L- parity, V- parity and L&V parity. 2- Find the Hamming code of the last byte of the data only in which two error can be detected and one error can be corrected, calculate the transmitted bandwidth? how can reduce the transmitted bandwidth? Explain and calculate the reduced…
An input to an AM modulator is 500 kHz carrier with a peak amplitude of 20 V. The second input is a 10 kHz modulating signal that is of sufficient amplitude to cause a peak change in the output wave of ±7.5 V. find the sideband frequencies find the modulation index ● ● ● ● find the voltage peak amplitude of the carrier and the sidebands determine the maximum and minimum amplitudes of the AM signal determine the AM signal expression
Compare the approximate hybnd model do the he-modef for the CE Configurastion and denive the mathemorticol refartion Ships tthert exast befween the hybnid parameter and the re-madel paramelas. Using Circut chaq rams awd martfemertical. exprssions desscibe the pprt properhed of the emifer forlower Ċirtmif ant HS apphication to eleetromes engimcenng 2.
A) For the J-K FFs shown below, Given the waveforms. Determine the Q output waveform GT) Po Sals
Convert: -24-j7 to polar 25cjs16.26deg 25cjs196.26deg 25cjs(-196.26)deg 25cjs163.74deg None of these Convert: j70-240 to polar 250cjs(-196.26)deg 250cjs(-16.26) deg 250cjs(-163.74)deg 250cjs196.26deg None of these
If 5 signals entered to a device, at 3dBm each, find the output power in dBm a. 15.dBm b. 10dBm c. 15dB
Discrete Signals and Discrete Time systemsx[n1] = (values) 9 random integer values from -10 to 5x[n2] = (values) 9 random integer values from -5 to 5 a. Plot the graph setting the middle integer value at n = 0 showing the all samples.b. Plot the graph x[-n] showing all the samples.c. Plot the graph x[n-3] showing all the samples.d. Plot the graph x[n+2] showing all the samples.e. Plot the graph x[2n] showing all the samples.f. Plot the graph x[n/3] showing all the samples.g. Evaluate the convolution of x[n1] and x[n2].
Problem 4: Two lowpass signals each band limited to 3 KHz are to be time multiplexed into a single channel using PAM. Each signal is impulse sampled at frequency of 50% above the Nyquist frequency. The time multiplexed signal wave form is filtered by an ideal LPF before transmission. f1(t) LPF PAM Signal Sampler f2(t) LPF Pulse Clock Gen. a. What is the minimum clock frequency of the system? b. What is the minimum cutoff frequency of the LPF? In the receiver, the signal is impulse sampled and demultiplexed using the system shown, determine the minimum and maximum acceptable BW of the LPF used in retrieving the analog signals.