150 mm 160 mm B 240 mm 130 mm 400 mm Q W Fig.P2.136

Q: 2) The truss is carrying two masses m (mg=100 N). It is supported by a rope at A and pin support at…

A:

Q: Let F₁ = [F1] N and let F₂ = 350 N. g) Determine the magnitude FA of the force at pin A. h)…

A: Given data: F1= 839 N  F2= 350 N  Free Body Diagram of the member AB:

Q: Name SURNAME: Student ID: QUESTION 9 The AE cable carrying the concentrated loads is attached to the…

A: a = 2m  b = 8m  c = 4m  d = 6m  Load P = 20 kN  We have to find out the followings:  Drawing…

Q: ituation 2: Determine the forces in cables AC and AB needed to hold the 20-kg ball D in equilibrium.…

A: GIVEN- Mass of the ball D = 20kg Force F =300N

Q: 660 lb/ft Find the force that pin D exerts on link BD. 550 lb/ft |Fp[ = 5.4 ft ii) Find the…

A:

Q: Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter…

A: Given Esteel=200 Gpa  a= 1 m, b= 1.5 m, d= 40 mm, h= 10 mm

Q: 3. Crossed members AG and BF are pin connected at E and a rope connected at C and D. Determine the…

A: Determine the tension on the rope and the horizontal and vertical components of forces at E.

Q: L2 La L, D Ls F Bar AB is supported by pin A and cable BC. Find the reactions at support A and the…

A: Reaction: The force or the moment which are exerted on a body due to its supports are called…

Q: 1.2 m 25° 40° 2 kN D 1.2 m 1.2 m E

A:

Q: 0.15 m 0.4m 0.2 m 03 m 0.5 m 0.25 m 0.2 m

A: The position vectors and unit vector are as follows: rCD=(-0.2i-0.3j+0.25k) munit…

Q: Determine the magnitudes of tension forces in rope AB, AC and AD for equilibrium of the ring A. (b)…

A:

Q: ecause the cable passes over a small pulley at B, the tension may be as he cable. Assume a = 3 in. A…

A:

Q: EDetermine all forces acting on body A Fort A for the System shown in Fignreca). Body A weighs(200N…

A:

Q: The rigid beam is supported by a pin at D and cables at AE and CF. If the load P is applied at B on…

A: A rigid beam is hinged at D, the beam can rotate about D but it cannot deform.A load P is applied at…

Q: Problem Number 4. The steel truss was subjected to horizontal force 2kN at C. Find the member forces…

A: P = 2KN

Q: If the connection at joint C of the frame in figure below is rigid (fixed) connection, then the…

A: Given data Frame Point load Member length As C is rigid joint and there is roller support at B hence…

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Answer  Influence line diagram for member DI Consider a vertical section passing through DI as shown…

Q: The frame ACD is supported by ball-and-socket joints at A and D and by a cable that passes through a…

A:

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5…

A:

Q: Weight W is supported by spring OC, which is attached to two cables at O. The un-stretched length of…

A:

Q: The steel truss was subjected to horizontal force 2kN at C. Find the member forces of AC using the…

A: Calculation of Member forces in AC using Unit Load METHOD##

Q: 2P 1.5P P 1.5P 2P , hinge B. D 15m 7m 7m 4@10m = 40m

A:

Q: FI1-1. Determine the required magnitude of force P to maintain equilibrium of the linkage at 0= 60°.…

A: Draw FBD:

Q: Pr: Determine al forces acting on body A for tue System shown in Figureců). Body A weighs (200N and…

A: its a problem of mechanics simply analysing forces on a body given surface is smooth so no friction…

Q: The homogeneous bar shown is supported by a smooth pin at C and a cable that runs from A to B around…

A:

Q: Cable AB is supported by a truss structure at A and a pin at B. A uniform distributed load is…

A: 50

Q: Determine the resultant force at pins A, B, and C on the three-member frame. P=129 N q=200 N/m

A: Load P = 129 NLoad intensity q = 200 N/m

Q: Determine the forces in members AC and AD of the loaded truss. 1.2 m 25° |40 B Y2 kN 1.2 m 1.2 m_ E

A: A truss is a structure with straight members creating triangles to support a load. The members of…

Q: Q2. (а) A beam is supported and loaded as shown in Figure Q2(a). Point A is a M UTM pin support and…

A:

Q: The bracket BCD is hinged at C and attached to a control cable at B. For the loading shown,…

A: Consider the figure,

Q: Compute the reactions at A and D. Determine the internal forces in each member of the truss using…

A:

Q: Find the stresses in the wires P1, P2, P3 shown if their diameters are 100mm  each and P3=20kN and…

A: Given data: R=40 Kn P3=20 Kn   It is asked to calculate forces P1 and P2

Q: a. Maximum tension on member DI in kN, put "O" if none. b. Maximum compression on member DI in kN,…

A:

Q: A 300 mm M 30 mm 30 mm B. 150 mm 150 mm a) Determine the bending stress developed at point A. b)…

A:

Q: 4. Select member FC and CB in the truss to carry the inclined force P. Set the allowable tensile…

A:

Q: P:Determine all forces acting on body A for the System shown in figurecs). Body A weighs(200N) and…

A: ANS 1 appplying free body diagramme  showing all force components on boby A

Q: Q1) Determine the force in member BC of the truss shown, the truss is hinged at A and supported on…

A: