13.81 Consider the stagnation tube of Figure 13.6. If the uncer- tainty in the manometer measurement is 0.1 mm, calculate the ve- locity and the uncertainty in the velocity. Assume that C₂ = 1.00, Pair = 1.25 kg/m³, and the only uncertainty is due to the mano- meter measurement. nut S Stagnation tube Figure 13.6 Deflection

13.81 Consider the stagnation tube of Figure 13.6. If the uncer- tainty in the manometer measurement is 0.1 mm, calculate the ve- locity and the uncertainty in the velocity. Assume that C₂ = 1.00, Pair = 1.25 kg/m³, and the only uncertainty is due to the mano- meter measurement. nut S Stagnation tube Figure 13.6 Deflection

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

B1. A crude oil of specific gravity 0.75 is flowing through a pipe of diameter 325 mm and the frictional head loss of 5.5 m of crude oil between the two ends of a pipe which are 675 m apart. Calculate the Reynold's Number, discharge of crude oil in the pipe. Take co - efficient of friction as 0.0075 and kinematic viscosity as 10 stokes. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) The velocity of flow of oil in the pipe is (m/s) The Reynold's Number for the flow is Discharge of crude oil through pipe (in m3/s) is
hsllo
An oil and gas company wants to measure the flow rate of the oil in a low head loss application. 1. Suggest a suitable flow measuring device 2. Explain its different parts and working principle. 3. Draw neat sketch and marks its parts.
A) What is the apparent viscosity (Pa.s) of blood that is experiencine a shear rate of 52 s^-1? Assume the blood has a yield stress of 0.005 pascals and a value of 2 cP^1/2 for the parameter.
attached file again please , thank you.
Only question 10.6
12. A flow meter is placed into a horizontal 20 cm diameter line that carries 25 kg/sec of water. If the throat diameter is 16 cm; (i) Identify the flow meter type (ii) Check the flow characteristic (iii)What differential pressure may be expected across the pressure taps? Consider the water temperature is 40°C.
For the duct system, plot required fan head Hrequired (mm of water column) as a function of volume flow rate V. (Lpm). On the same plot, compare available fan head Havailable versus V. , and mark the operating point. Discuss.
Elevation = 100 ft D¸ = 1 ft (1) l (1) e, = 1000 ft D2 = 1 ft lz = 500 ft B V Elevation = %3D 20 ft (2) D3 = 1 ft (3) Elevation = l3 = 400 ft O ft Three open reservoirs are connected by pipes as shown above. It is assumed that the pipe diameter is equal to the friction factor of 0.03. Because theratio of the LIDpipe is large, the minor losses are ignored. Determine the flow in or out of each reservoir! Draw with sketch 5.
A pitot-static probe is used to determine the flow velocity by measuring the differential pressure as shown in Figure 7. The pressure difference sensor used in the system is electronic types and the output of the device is measured in voltage. The output of the pressure device is 3.5 V and the linear relationship between the device and the pressure difference is 10 kPa/v. i. Derive pitot formula to obtain flow velocity from Bernoulli equation, ii. Calculate the pressure difference inside the system, iii. Determine the velocity inside the system if the the fluid is water, and iv. Explain the cause that / ontirbute to inaccurary in the velocity reading. Fluid Flow, V Stagnation Static pressure pressure Pi-P2 Figure 7: Pitot static probe
B1. A crude oil of specific gravity 0.75 is flowing through a pipe of diameter 275 mm and the frictional head loss of 5 m of crude oil between the two ends of a pipe which are 525 m apart. Calculate the Reynold's Number, discharge of crude oil in the pipe. Take co - efficient of friction as 0.007 and kinematic viscosity as 10 stokes. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) The velocity of flow of oil in the pipe is (m/s) The Reynold's Number for the flow is Discharge of crude oil through pipe (in m3/s) is
Find the flow rate through the siphon and the pressure at the siphon apex. E.L. 130 m 물 -E.L. 120 m 1=1,500 m d=20 cm f=0.018 FE.L. 100 m Consider reasonable K s c, K s e, Kb values. 1=1,500 m