13. A pupil follows the route shown in the diagram and arrives back at the starting point. 150 m 40 m 40 m start / finish 150 m Identify the row in the table that shows the total distance walked and the magnitude of the final displacement. total distance (m) final displacement (m) 80 380 A B

13. A pupil follows the route shown in the diagram and arrives back at the starting point. 150 m 40 m 40 m start / finish 150 m Identify the row in the table that shows the total distance walked and the magnitude of the final displacement. total distance (m) final displacement (m) 80 380 A B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The head loss due to flow of a fluid inside a pipe is calculated from .L V? D 2g h Loss where Loss f = friction factor L = pipe length (m) D = pipe diameter (m) V = average flow velocity (m/s) g = acceleration due to gravity (m/s²) What is the appropriate unit for friction factor f?
Please show all steps in detail and make please show all formulas used. Subject is fluid mechanics
Introduction Structural analysis is important for designing all type of structure including truss structure. There are several method to analyse truss structure. Therefore, student should be able to analyse the truss structure with appropriate method. This assignment is given to student to evaluate the ability of the student in solving the complex problem involving truss structure as shown in Figure 1 below. B 6m 88) O 20kN By using an appropriate method, i) 6m 20kN/m D 30KN Figure 1 6m H 20KN 6m LL G Figure 1 above shows a truss structure, which is supported at A and G. The truss is design to support a uniform load 20kN/m from C to E as shown in the figure. Given the elastic modulus, E=200GPa, and the cross-sectional area for member AJ, JI, IH, and HG is equal to 500mm² while other members is equal to 250mm². Based on the details given, solve the following task to analyse the truss structure. Task 1 8m Describe the determinacy and stability of the truss structure. Your answer must be…
At a given instant the roller A on the bar has the velocity v = 4 m/s and acceleration a = 7 m/s? . (Figure 1) Determine the bar's angular velocity at this instant measured counterclockwise. Express your answer using three significant figures. Enter positive value if the angular velocity is counterclockwise and negative value if the angular velocity is clockwise. Wbar = 6.67 rad/s Submit Previous Answers v Correct Figure 1 of 1 Part D Determine the bar's angular acceleration at this instant measured counterclockwise. Express your answer using three significant figures. Enter positive value if the angular acceleration is counterclockwise and negative value if the angular acceleration is clockwise. vec 30 0.6 m abar = 23.817 rad/s? 30 Submit Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining
Consider (Figure 1) Figure 60° 20 ft < 1 of 1 ▼ Part A Determine the minimum initial velocity up at which the ball must be kicked in order for it to just cross over the 8-ft high fence. Express your answer using three significant figures and include the appropriate units. Ti μA 3 C ? v0 = Units Submit Request Answer Part B Determine the corresponding time t at which the ball reaches the fence Express your answer in degrees using three significant figures. IVE ΑΣΦ 11 vec C ? Value
If the section shown in the figure turns from fully-elastic to fully-plastic, the depth of neutral axis (N.A), y, decreases by 60 y I 5 4 N.A. *20* ]] 60
Consider (Figure 1). Figure Vo 00 6 m 3 m ▼ Part A Determine the minimum initial velocity vo at which the ball must be kicked in order for it to just cross over the 3-m high fence. Express your answer using three significant figures and include the appropriate units. v0 = Submit Part B 00 = μА Submit Value Request Answer Units Determine the corresponding angle o at which the ball must be kicked. Express your answer in degrees using three significant figures. AΣ vec Request Answer **** *** ? ***** ***** ? O
Compute the deflection of a structural member made of aluminum if a load of 755 N is applied to the bar. The member has a uniform rectangular cross section with the dimensions of 6 mm × 100 mm , as shown in the accompanying figure.
Numerical analysis-doing by matlab
In (Figure 1), F = {80i + 96j + 48k} lb. Figure 1 ft -2 ft 3 ft 45° B 1 of 1 Part A Determine the magnitude of the moment of F about point A. Express your answer in pound-feet to three significant figures. 15] ΑΣΦ11 MA = Submit Part B α, B, y = Submit Request Answer Provide Feedback Determine the coordinate direction angles of the moment of F about point A. Express your answers in degrees to three significant figures separated by commas. vec U/ ΨΕ ΑΣΦ ↓↑ vec Request Answer ? lb. ft ? Next >
show complete solution, the formula used, figures and explanation
2