Structural Analysis
6th Edition
ISBN: 9781337630931
Author: KASSIMALI, Aslam.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Related questions
Question
Two plates are welded as shown. As per NSCP specifications, the effective area of fillet welds shall be taken as the effective length times the effective throat thickness and the maximum size of fillet welds that is permitted along the edges of connected parts shall be:
* Material less than 6 mm thick, not greater than the thickness of material
* Material 6 mm or more in thickness, not greater than the thickness of material minus 1.6 mm.
The plates are 12 mm thick and 350 mm wide. Nominal tensile strength (Fu) of weld is 550 MPa. Allowable shear stress is 0.30Fu.
1. Which of the following most nearly gives the maximum size of fillet weld, in mm?
a. 11
b. 12
c. 10.5
d. 11.5
2. Which of the following most nearly gives the effective area of the weld, in mm²?
a. 2573
b. 3614
c. 2810
d. 3700
3. Which of the following most nearly gives the safe value of tensile force P, in kN?
a. 424.6
b. 360.10
c. 520.5
d. 430.7
Transcribed Image Text:12mm thick
350 mm
P
P
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by stepSolved in 2 steps with 2 images
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- The effective throat thickness of a fillet weld not to be greater than a. 0.3t b. 0.6t C. t d. 0.5tarrow_forwardTopic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem The angle 150x100x10mm is connected to a 8.5 mm gusset plate. The size of weld is 8 mm and using E70 Electrodes. Fu = 438 MPa. Use LRFD. Questions: a) Find the length of the weld required at the toe of the angle. b) Find the length of the weld required at the heel of the angle. c) Find the block shear strength of the gusset plate.arrow_forwardDesign a double angle tension member that is fillet welded to a gusset plate. Assume that the angles will be made from A36 steel, and the gusset plate from A572 Gr. 50 steel. Use 70ksi electrode. Design the system to resist a factored load of 200 kips. Check all applicable limit states that are possible. Provide your results on a sketch with standard weld symbols and details.arrow_forward
- What is the diameterarrow_forward5. Select a pair of channels and design the fillet welds using SMAW process. The loading is 85% live load and 15% dead load. Compare for (a) A36 steel (b) A572 Grade 60 steel 200k 2-Channels W sectionarrow_forwardCentroid + Inertia 200 x 20 mm Plate The strength of the rolled section shown is increased by combining S section, channel, plate and then welded. 1. Determine the location of its centroid; and 5310 x 47.3 C310 x 30.8 2. Determine the moments of inertia of the composite section with respect to its centroidal x and y Semi-circle Weld, 10mm radius axes.arrow_forward
- Determine the size of the weld using E60 electrode. Dead Load = 38 kip and LL = 95 kips (Service Loads) 10 in- 10 in- -10 in W = ?arrow_forwardWhich of the following is true of slip-critical type connections? O Load is transferred by sehar O Load is transferred by bearing of bolts against the hole O Load is transferred by moment O Load is transferred by the friction resistance of the connected partsarrow_forwardTwo steel plates, each 400mm wide and 12mm thick, are to be joined together by a lap splice (single). The electrode to be used for the weld has a nominal tensile strength of 550Mpa. Determine the following:a. the maximum weld size that can be usedb. effective net area of the fillet weld using the maximum weld size allowed by the manualc. the maximum load that can be resisted by the weld using the maximum weld size allowed by the manual.arrow_forward
- 7. /8 Using the figure below, answer the following: a. What type of weld is to be made? b. What is the significance of the square on the reference line? c. What is the depth of preparation on the arrow side? d. What is the effective size of the weld on the other side? True (³²³)arrow_forwardRegardless of the design load, the effective length of a 5/8 in. fillet weld that is subjected to stress in a longitudinal direction should not not be less than A. 2 in. B. 2 1/2 in. C. 3 in. D. 3 1/2 in.arrow_forwardIf the thickness of plate to be connected by a rivet is 16 mm, the suitable size of rivet will be (a) 16 mm (c) 24 mm (b) 20mm (d) 27 mmarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill Education
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning