12.a. The easiest place to install an ammeter into a stepper motor driver/motor circuit for system diagnostics is to A. connect the meter across the center tap and phase leads of the motor. B. remove a fuse and place the meter leads across the fuse clips. C. attach the meter in series with the driver’s power supply lead. 12.b. A type of feedback device that uses a rotor and senses the position of the motor by means of sine and cosine waveforms is called a/an A. resolver. B. tachometer. C. alternator.

12.a. The easiest place to install an ammeter into a stepper motor driver/motor circuit for system diagnostics is to A. connect the meter across the center tap and phase leads of the motor. B. remove a fuse and place the meter leads across the fuse clips. C. attach the meter in series with the driver’s power supply lead. 12.b. A type of feedback device that uses a rotor and senses the position of the motor by means of sine and cosine waveforms is called a/an A. resolver. B. tachometer. C. alternator.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

25.a. There are two wires labeled P1 and P2 at a DC motor's junction box. These wires will attach to whatinternal component of the motor?A. A speed potentiometerB. The parallel windingC. GroundD. A thermostat25.b. As you walk up to a machine, you see a technician tapping on the back section of a DC motor with alead mallet. This technician isA. cleaning the commutator.B. checking for end bell cracks.C. looking for weak or worn brushes.D. reseating the rear end bell on the case.
6- The injected e.m.f in the rotor of induction motor must have (a) The same frequency as the slip frequency. (c) A high value for satisfactory speed control. (d) The same phase as the rotor e.m.f and a high value for satisfactory speed control. (b) The same phase as the rotor e.m.f.
9.a. A servo system is oscillating at standstill. This is an indication thatA. the following error limit has been exceeded.B. a motor winding is open.C. the system gain is too high. 9.b. In a DC servo motor system, the tachometer feeds back a voltage that’s proportional to motor speed.Where does this voltage go to?A. The interpolator cardB. The driverC. The CPU in the main controller
c) What is the physical meaning for each of the following induction motor parameters: R1 „R2 ,Rc ,X1 ,X2 ,Xm ?
Problem 1 For each of the following mention, explain with waveforms, and draw diagram of 1. A circuit to drive a DC motor in two quadrants only FM and RB. 2. Speed control of IM by adding a resistance in the rotor. 3. A circuit to drive a DC motor in four quadrants. 4. The relation between the frequency and speed of IM.
Draw the harmonic current waveform and harmonic order for current drawn by an adjustable speed motor drive.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC MACHINES Answer the following questions (A, B and C) depending on the topic. 1. SYNCHRONOUS MOTORS A. What is necessary to start a synchronous motor to rotate from standstill? Describe the process. B. What is meant by synchronous condenser? C. Why is it possible for synchronous motors be used as a power factor correction device and what applications do synchronous motors commonly used? Describe the operation.
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights.
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights. design the single-phase, full-wave, ac/ dc converter. show design specifications, the reason for DC motor selection. correct manual circuit, and correct automatic closed-loop control circuit
What is the function of a commutator? A. Double up as a frequency converter that can change the supply frequency from the regulator. B. Double up as a frequency converter that can change the supply frequency from the rotor. C. Change the position of the brush gear. D. Vary the input voltage
A synchronous machine is a three-phase, two-pole machine with 36 stator slots and 5/6 full-pitched balanced armature windings. Each phase winding is made up of eight identical coils connected in sequence. Balanced three-phase 66 Hz currents with a peak amplitude of 16 A are used to drive the stator phases. a) What is the basic stator space mmf's maximum amplitude? (A.turns) b) How fast does the fundamental stator space mmf rotate mechanically? (rpm) c) What is the third-harmonic stator space mmf's maximum amplitude? (A.turns) d) What is the fifth-harmonic stator space mmf's maximum amplitude? (A.turns) e) How fast does the fifth-harmonic stator space mmf rotate mechanically? (rpm)
5.a. A characteristic common to most steam-turbine alternators isA. belt drive.B. salient-pole rotor construction.C. gear drive.D. cylindrical rotor construction.5.b. The stator core of an alternator is safeguarded against high short-circuit current by a device called aA. surge capacitor.B. lightning arrester.C. differential protector.D. temperature detector.