Answered: # 12. Find the phase relationship…

Engineering

Electrical Engineering

# 12. Find the phase relationship between the following waveforms; =100 sin (ot- 80) i = 0.1 sin (ot – 20)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: For the amplitude and phase spectrum shown in figure below, The Compact Fourier series is: 3 456 7 8...

A: The solution is given below

Q: • T or F, modify the wrong part if False, please underline twice your answer if True or False. ...

A: Transformer is a two winding device and works on mutual induction . When primary winding is excited ...

Q: R 3kohms V1 R_L 20V D1 10KO 25% Key-A Vz= 8V When the varistor is set to 25%, compute the following ...

Q: 4) A+АB O 1 А В

A: Given expression, A+AB

Q: A center-tapped FWR circuit have an output dc voltage of 54 V. What is the PIV rating for the diodes...

Q: 3.29 Find v, and the total power dissipated in the circuit in Fig. P3.29. SPICE LTISIM Figure P3.29 ...

A: The solution is given below

Q: iar at a polnt between them 24 cm from q1? 2. Three point charges q, = +2.7µC, q2 = -3.4µC and q3 = ...

A: The solution is given below

Q: Si R 1.5 kn VR E 30 V FIG. 2.154 Problem 4.

Q: T or F, modify the wrong part if False, please underline twice your answer if True or False. A 100...

A: Voltage regulation is defined as the rise in voltage from full load to no load , exprrssed as a frac...

Q: The humper Bridge in England has the world's longest single span, 1410 m. Calculate the change in le...

Q: R1 2 1k2 V1 +] 10V Si Vo 1kHz 0° Circuit A V5 1,

Q: Find IR, Iz, IL PL, PR1 and the ideal power rating of R1 & RL D1 V1 R1 16 Vrms 60 Hz 0° 2500 1B4B42 ...

A: Power rating: Power rating means how much loss occurs across the resistor. Its unit is the watt.

Q: For the emitter-stabilized bias circuit of Fig. 4.122 , determine: d. V C . e. V B

A: In this question ,BJT is given.....We have to find out emitter , collector and base voltage....

Q: The result of e = O a. -1 O b j O c. j Od 1

Q: How does wind energy works

A: Wind energy is used for the production of electricity through windmills. Windmills are the devices w...

Q: Reference (Figure 2.1) With switch SW1 open, calculate the maximum power (in W) that can be transfer...

Q: 2. Obtain the transfer functions V1(s)/V2(s) of circuits in figures R (b)

Q: The second question: a wheel rotates from rest with uniform angular acceleration, and its speed reac...

Q: 2, Find Inverse Laplace transform for the following functions: s+7 4 a) F(s) = %3D s2 - 6s + 8 s2 + ...

A: The solution is given below

Q: Find the response i(t) of the RLC series circuit for t>0 i t = 0 ll Vs Case 1 Case 2 Case 3 L=0.1H L...

Q: A certain battery with potential difference of 2 Volts can deliver 10 Joules of energy, determine th...

A: Voltage is defined as The work done per unit charge So use the definition V = W/q volts Units of wo...

Q: -Find RL through Norton's Theorem when the switch is open.

Q: For the circuit shown, a) Determine the load impedance that will result in maximum average power bei...

A: Maximum power theorem: This states that in the circuit load resistance is equal to the source resist...

Q: II. FIND THE RECTANGULAR FORM OF THE FF: 4. 15ei25° 5. бе

A: Polar form is in the form of re^theta and reactangular form is rcos(theta)+jrsin(theta).

Q: Find the current required by a 400 V, 10 H.P. DC motor at 73.55% efficiency.

A: Given: A DC motor having, Output power rating, Po = 10 HP = 7460 W Efficiency, η=73.55 % Input volta...

Q: • T or F, modify the wrong part if False, please underline twice your answer if True or False. S...

A: FALSE The given statement is FALSE for the given synchronous motor or generator synchronous motors a...

Q: 25 V t = 0 4 H Turn on the circuit and findt = 1,t = 2, t = 3, t = 4, t = 5

A: After turn on the switch , inductor and 2 ohm resistor become short.

Q: Compare FET amplifiers over BJT amplifiers?

A: Consider few of the difference between the FET and the BJT are listed in the table.

Q: (b) 2 4 R(s) C(s) -/-

A: In this question, Reduce the given signal, and find the transfer function C/R? We know closed loop...

Q: A boost converter with an input voltage of 5 V dc and an output voltage of 8 V dc will have a duty c...

A: Given a boost converter with, Input voltage, Vs=5 V Output voltage, Vo=8 V Duty cycle, α=?

Q: b) Determine the value of the capacitor and inductor of a series resonance circuit exhibiting the fo...

Q: A three-phase delivers 120 kVA to a three-phase load at a line-to-line voltage of 2400 V. Calculate ...

Q: 1. A metallic conductor has a resistivity of 18 x 100m. What is the resistance of a piece that is 30...

Q: A 415V TPN busbar rising main chipped to a surface is to provide a 240V supply to each of 8 individu...

A: Answer - Following is the circuit arrangement showing how each flat must be connected to the rising ...

Q: Q9. A series motor having a series field resistance of 0.25 2 and an armature resistance of 0.15Q is...

Q: Theoretical calculations: 1. Draw the spectrum of AM-SSB ? 2. What is the minimum band width require...

A: We are authorized to answer three sub-parts at a time, since you have not mentioned which part you a...

Q: A 415V TPN busbar rising main chipped to a surface is to provide a 240V supply to each of 8 individu...

A: Solution- The circuit arrangement from the above data- It is showing how each flat must be connect...

Q: Consider a 7-bit ADC and full scale voltage measurement range of (0-45).The Resolution will be O 0.3...

A: Given , Full scale voltage measurement range = (0-45) V Number of bits represents to each voltage le...

Q: What is the decimal number 767435 in base 63? (Hint: use the ascii array from A1!)

A: In this question, We need to convert decimal number to base 63. The given decimal number 767435

Q: After being open for a long time, the switch on the figure below is closed at t = 0. For t > 0 s, fi...

Q: Define the Signum function.

A: In this case, the signum function is to be defined.

Q: 11)Refer to the diagram below and answer all parts of Question 11. R. R1 R2 R3 Vs Dz D1 D2 D3 Vs = 2...

Q: T or F, modify the wrong part if False, please underline twice your answer if True or False. For a...

A: Total copper losses in shunt wound machine is sum of the armature copper losses and shunt field copp...

Q: Ex (1):- A digital optical disc (CD) storage records video signals digitally by using PCM. Assume th...

Q: At a particular instant an inductance of 1 H carries a current of 2 A while the voltage across it is...

A: Consider the energy stored in the inductor is, E=12Li2

Q: 4. Derive the logic function for the following circuit diagram у —

A: Given: Logic circuit

Q: 6) It is required to generate a single pulse waveform (Vtrigg) of 4 Volts amplitude (peak-to peak) a...

Q: Consider the following circuit :22 :302 32 ww- 32 ww- ww Aww + 6 V ww- ww

Q: Diode D1 connected to Vbe of NPN transistor.18 with forward biased of while D2 connected to the Vbe ...

A: Find the Vbe of diode D1 is which connected across NPN transistor and Vbe of diode D2 which is conne...

Q: Explain the relationship between bits per second and baud for an FSK system.

A: FSK system- In FSK Frequency of carrier signal varies according to the message signal. The output of...

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

# 12. Find the phase relationship between the following waveforms;
100 sin (ot - 80)
i = 0.1 sin (ot – 20)
V =

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The inductive reactance (XL). be affected by the harmonics of non-sinusoidal .wave all-of-them O could O cannot O will O
can you please give me the comple solution for this question, thanks. A certain voltage function contains a constant term, a fundamental and third harmonic. The maximum value of the fundamental is 85 % of the constant term and the maximum value of the third harmonic is 55 % of the constant term. If the effective value of this function is 180.3V, find the magnitude of the two harmonics. A.IstHarmonic = 75 V , 3rd Harmonic = 120V B. Ist Harmonic = 80 V , 3rd Harmonic = 125V C. IstHarmonic = 120 , 3rd Harmonic = 75V D. Ist Harmonic = 125 V , 3rd Harmonic = 80V E. NOTA
The relation between the effective value and the maximum value of a sinusoidal voltage is
Apply a sinusoidal input voltage with 2V p-p and vary the frequency according to the table below. Measure the voltage Vr and current I from the voltage across R and find the phase angle between the Vi and I.
The sinusoidal current waveform having the R.M.S value of 25 A, then the maximum value is
The rms value of the resultant current in a wire carries a dc current of 10 A and a sinusoidal alternating current of peak of value 20 A is-
coil of watt meter is connected in series.
3. For a sinusoidal input of 20 Vpe to the given circuit, what is the peak value of the output waveform? V-5V a) 20 V b) 25 V c) 0 V d) -25 V
A voltage wave of 250 kHz has a Vmax-5 V and Vmin=-35 V. The duty cycle of this wave is 0.875. This voltage waveform has been applied across a 2.5 µH inductor for a very long time so that steady state has been achieved. Diagrams of the wave parameters and circuit are shown in this figure: L What is the average voltage of this wave? Average voltage = 35 V Voltage (arb, unit) 1.25 Minimum current: -3.5€ Amps 1 0.75 0.5 0.25 0 4.25 05 Have you integrated the wave over full cycle? 4.75 4 -1.25 Vmax 0.5 Vmin What is the average current flowing through the inductor? Average current = 3.56 A 15 Period/s On average, there is no power consumed by the inductor. Have you considered this? What are the maximum and minimum currents that flow through the inductor? Maximum current: 0.50 Amps D= 25 TH TH Have you used the relationship for current and voltage in an inductor? Have you considered the slope of the current wave?
What are the phase relationships between the following waveforms?
In a symmetrical sinusoidal waveform, the negative peak is more than than positive peak. Select one: True False
The r.m.s. value of a sinusoidal current of maximum value 95 A is,