12. Draw the Timing diagram for INR M.> Fetching the Opcode 34 from the memory 4105H.Let the memory address (M) is 4250H.Let the content of that memory is 12H.> Increment the memory content from 12μ to 13μ-Address4105MnemonicsINR MOpcode34H

Answered: Image /qna-images/answer/a70363b2-6fe1-4412-8d80-8f18c16816a7.jpg

12. Draw the Timing diagram for INR M. ► Fetching the Opcode 34 from the memory 4105H. > Let the memory address (M) is 4250μ > Let the content of that memory is 121. > Increment the memory content from 12 to 13. Address Mnemonics Opcode

12. Draw the Timing diagram for INR M. ► Fetching the Opcode 34 from the memory 4105H. > Let the memory address (M) is 4250μ > Let the content of that memory is 121. > Increment the memory content from 12 to 13. Address Mnemonics Opcode

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

d) Given the values stored in the following register. Calculate the physical address for each of the following: i. ii. iv. if CS = 2000H, and IP = 1000H if DS = 1000H, and BX = 0010H for the memory address 0100:1234H
2. Memory contents (in hexadecimal) are 0005, 0001, 0123 for addresses 000 to 002, then 2002, 1000, 7800, F400 for addresses 80A through 80D. AC starts with value 0F24, PC has the value 80A, and AR has the value 4F5. Starting with time-step T0, describe what happens until the next TO. Make sure to indicate any updated register values as they happen. (Assume R= 0.) Refer to table 5.6 from Mano's textbook. F24 1 AR
Q2. Interface 4 digit displays (each digit is a 7-segment display) to the 80386DX microprocessor (32 bit data bus and 32 bit address bus) using 8255 PPI. The 8255 should function at I/O addresses that start at 200H. Then write a program to initialize the 8255 and multiplex the 4 digit display where the data, in 7-segment code, that is to be displayed is stored at memory location 2000H: 0100H.
Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es. If applicable, determine the content of the destination after the execution of the instruction. Otherwise, NA. For physical address and content of the destination, use CAPITAL LETTERS,NO SPACE/S in between and NO need to include "H" or the unit. If the given register are fewer than required, just put zeroes in the most significant place. A -effective address B - physical address/es e.g. 19000-19001 C- is for addressing mode type, e.g. direct D- content of the destination after execution e.g. if register: AX=1234 if memory (lower address first): 12000=34;12001=12 3(2).JPG ... AX =6FFAH DX =BFA8H SS = 6FFEH SI %3D 2BCАН IP = FADEH ВХ -9CF5H CS =5FFEH ES = 8DBEH BP = 6EEFH CX =3FFEH DS =AF9EH DI = 5EC9H SP = 9AABEH MOV [BX+SI+ADBCH], ESP EFFECTIVE ADDRES: Blank 1 PHYSICAL ADDRESS/ES: Blank 2 ADDRESSING MODE : Blank 3 CONTENT OF THE DESTINATION: Blank 4
In 8051 assembly language: If one of the elements in a list in ROM is more than 8 bits in binary as shown below list: DB 9H,12H,2021H How can I separate 2021 into 2 bytes in RAM? So that one location in RAM holds 20, and the other 21. (Values in RAM should be in BCD format)
Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es. If applicable, determine the content of the destination after the execution of the instruction. Otherwise, NA. For physical address and content of the destination, use CAPITAL LETTERS,NO SPACE/S in between and NO need to include "H" or the unit. If the given register are fewer than required, just put zeroes in the most significant place. A -effective address B - physical address/es e.g. 19000-19001 C - is for addressing mode type, e.g. direct D - content of the destination after execution e.g. if register: AX=1234 if memory (lower address first): 12000=34;12001=12 EFFECTIVE ADDRES: PHYSICAL ADDRESS/ES: ADDRESSING MODE : CONTENT OF THE DESTINATION:
Evaluate the following expression using three, two and one address machine format.X= (A-BX C)/(D+EXF)
liomework: Identify the addressing modes used for the source and destination operands, and then compute the physical address for the specified orx•rand in each of the following instructions: a) Mov +XYZ,AH (Destination operand) b) Mov tBX) (Destination operand) Suppose that BX=030016, 010016.
Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es. If applicable, determine the content of the destination after the execution of the instruction. Otherwise, NA. For physical address and content of the destination, use CAPITAL LETTERS,NO SPACE/S in between and NO need to include "H" or the unit. If the given register are fewer than required, just put zeroes in the most significant place. A -effective address B - physical address/es e.g. 19000-19001 C - is for addressing mode type, e.g. direct D - content of the destination after execution e.g. if register: AX=1234 EFFECTIVE ADDRES: PHYSICAL ADDRESS/ES: ADDRESSING MODE : CONTENT OF THE DESTINATION: if memory (lower address first): 12000=34;12001=12
Need detailed correct answer only. Incorrect and irrelevant solution will get Dislike.
A set of ten packed BCD numbers is stored in the memory location starting at 3050H. i. Write a program with a subroutine to add these numbers in BCD. If a carry is generated, save it in register B, and adjust it for BCD. The final sum will be less than 9999sCD. ii. Write a second subroutine to unpack the BCD sum stored in registers A and B, and store them in the memory locations starting at 3070H. The most significant digit (BCD4) should be stored at 3070H and the least significant digit (BCD) at 3073H.