12 12) The air conditioner removes 2.7 kJ of heat from inside a house with 450 m³ of air init. At a typical air density of 1.3 kg/m² that means 585 kg of air. If the specific heat ofair is 1.01 kJ/(kg °C), by how much would this cool the house if no heat got in throughthe rest of the house during that time?

The given values are - Q=2.7 kJ, m=585 kg, C=1.01 kJkg°CLet us take ∆T=Temperature change due to…

12) The air conditioner removes 2.7 kJ of heat from inside a house with 450 m² of air in it. At a typical air density of 1.3 kg/m³ that means 585 kg of air. If the specific heat of air is 1.01 kJ/(kg °C), by how much would this cool the house if no heat got in through the rest of the house during that time?

12) The air conditioner removes 2.7 kJ of heat from inside a house with 450 m² of air in it. At a typical air density of 1.3 kg/m³ that means 585 kg of air. If the specific heat of air is 1.01 kJ/(kg °C), by how much would this cool the house if no heat got in through the rest of the house during that time?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 6RQ: One British thermal unit will raise the temperature of _____ 1b of water _____F.

See similar textbooks

Similar questions

How many Btu of heat can be produced by 4 kWh ofelectricity?
One British thermal unit will raise the temperature of _____ 1b of water _____F.
A particular frost-free refrigerator uses about 745 kWh of electrical energy per year. Express this amount of energy in unit cal.
Based on the mechanisms of thermal energy exchange what would happen if you exercised in a colder place where it's 5⁰C.
In a refrigeration cycle, the refrigerant gains heat in the evaporator and in thesuction line. In a certain refrigeration system, R-134a gains 67.8 Britishthermal units per pound (Btu/lb) in the evaporator. It then gains 2.5 Btu/lb inthe suction line. Find in Btu/lb the total heat gained by the R-134a.
Evaluate the work and heat transfer, each in kJ per kg refrigerant
When you add heat to a system, by how much does its temperature change?
What is the Kelvin equivalent of 70 0F.
Answer the other probem (NOT 1C5) use 1C5 as a reference 1.C.5. The refrigerant in an evaporator goes through phase change at a constant temperatureof −30◦C. The rate of vaporization of the refrigerant is 0.15 kg/s. The latent heat of vaporization ofthe refrigerant is 412.1 kJ/kg. Air enters the evaporator at mass flow rate 1.1 kg/s with a temperatureof 45◦C. Assume air has a constant specific heat of 1007 J/kg·K. What is the effectiveness of this heatexchanger? It was found that the convection coefficient of air in the evaporator described in Example 1C.5 is350 W/m2·K, and the heat transfer surface area is 5.1 m2. What is the average convection coefficientof the refrigerant under these conditions? (Note: As the refrigerant is evaporating, it is also flowingin the heat exchanger. And since it is a flowing fluid, it will have a convection coefficient.)
Question: A piston cylinder device initially contains superheated steam as shown in the following figure. Then it starts losing heat and as result piston moves down to the set of stops where it contains saturated liquid water. The heat loss process continues until the system contains water at 473K. Determine, a) The final pressure and quality (if any) b) The boundary work c) Amount of heat total transfer Steam 0.35 kg 3.5 MPa Superheated by 7.4°C
2) The energy consumed by a shower for 30 days is 22kwh. It is known that the resistance of the showerhead is 20 ohms and that its nominal current is 15A. So, what is the time in minutes that the shower was turned on during this period?
A piston cylinder arrangement initially contains 7.0 kg of super-heated steam at 100 kPa and 250 oC, now heat is removed until 0.56 condenses. 1) What is the amount of heat removed in (kJ)? 2) What is the final volume (m3)?