11.54 In a balanced three-phase system, the source is a balanced wye with an abe-phase sequence and V=208/60° V rms. The load consists of a balanced wye with a phase impedance of 8 + j5 02 in parallel with a balanced delta with a phase impedance of 21+12 0. If the line impedance is 1.2 + j1 , find the phase currents in the balanced wye load.

11.54 In a balanced three-phase system, the source is a balanced wye with an abe-phase sequence and V=208/60° V rms. The load consists of a balanced wye with a phase impedance of 8 + j5 02 in parallel with a balanced delta with a phase impedance of 21+12 0. If the line impedance is 1.2 + j1 , find the phase currents in the balanced wye load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.19P: Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current...

See similar textbooks

Similar questions

A balanced delta connected load contains 8 + j4 ohms per phase, while a balanced wye connected loadconsists of 2 – j1 ohms per phase. Both loads are connected in parallel to a three-phase three-wire system inwhich the line voltage is 120 V rms at the loads. The three lines extending from the loads to the source eachhave a resistance of 0.2 ohms. Determine the power lost in the wires.a. 1.42 kW b. 1.38 kW c. 1.24 kW d. 1.83 kW ( please stay on choices, thanks) ..
In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
A balanced wye-delta system has a phase voltage of 24V RMS and a power factor of 61.5%. The total real power dissipated by the 3- phase load is 100W. Draw the system and calculate the magnitude of the load impedance.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the real, reactive, and apparent powers seen at load 1? Give also the power factor.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What is the total power drawn from the 3 phase source?
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: Give the value of reactive power per phase seen at load 2.
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: If the power factor for both loads will be changed to 0.95 lagging using a capacitor parallel to load network, what is the needed reactive power per phase to achieve the required power factor for load 1 and load 2 respectively? Give also the value of capacitace that must be added to reach the power factor for both load.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: If the power factor for both loads will be changed to 0.95 lagging using a capacitor parallel to load network, what is the needed reactive power per phase to achieve the required power factor for load 1 and load 2 respectively?
A balanced three-phase source having a line voltage of 208-V rms is supplying two parallel-connected three-phase loads. The first load is a balanced delta of impedance 21 angle 30° Q per phase and the second load is a balanced wye of impedance 9 angle -60° Q per phase. Find the magnitude of the rms line current and the total average power absorbed by the load.
A balanced three-phase source having a line voltage of 208-V rms is supplying two parallel-connected three-phase loads. The first load is a balanced delta of impedance 44 angle 30° Q per phase and the second load is another balanced delta of impedance 50 angle -60° Q per phase. Find the magnitude of the rms line current and the total average power absorbed by the load.