11) A support block is acted upon by two forces as shown.Knowing that the coefficients of friction between theblock and the incline are μs 5 0.35 and Mk 5 0.25,determine the force P required (a) to start the blockmoving up the incline, (b) to keep it moving up, (c) toprevent it from sliding down.800 N

Given data as per question μs=0.35μk=0.25

11) A support block is acted upon by two forces as shown. Knowing that the coefficients of friction between the block and the incline are μs 5 0.35 and Uk 5 0.25 determine the force P required (a) to start the block moving up the incline, (b) to keep it moving up, (c) to prevent it from sliding down.

11) A support block is acted upon by two forces as shown. Knowing that the coefficients of friction between the block and the incline are μs 5 0.35 and Uk 5 0.25 determine the force P required (a) to start the block moving up the incline, (b) to keep it moving up, (c) to prevent it from sliding down.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.3P: Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair...

See similar textbooks

Similar questions

The foot of a uniform ladder, of length 2a and weight W, rests on rough horizontal ground and the top of the ladder rests against a smooth vertical wall, The ladder makes an angle of 60° with the horizontal. A man of weight 4W climbs up the ladder. Given that the ladder begins to slip when the man has climbed two-thirds of the way up the ladder, find (a) the coefficient of friction between the ladder and the ground, (b) how far a boy of weight 2W can climb up the ladder before it slips.
A support block is acted upon by two forces as shown. Knowing that the coefficients of friction between the block and the incline are u, = 0.35 and H = 0.25, determine the force 25°f P required to (a) start the block moving up the incline, (b) keep it moving up, (c) prevent it from sliding down. 800 N
A support block is acted upon by two forces as shown. Knowing that the coefficients of friction between the block and the incline are us and uk determine the values of P. Neglect the weight of the block. Given: F= 908 N e= 22° Hs =0.33 Pmin = Pmax = P.
Knowing that the coffiesient of static friction between all the surfaces is 0.3 find the value of the force p required to initiate motion of the 200 N block if: 1. The force p is applied to the left 2. The force p is applied to the right
A support block is acted upon by two forces as shown. Knowing that the coefficients of friction between the block and the incline are μs = 0.35 and μk = 0.25, determine the force P required to (a) start the block movingup the incline; (b) keep it moving up; (c) prevent it from sliding down.
Activity 2. What weight W is necessary to start the system of blocks shown to the right? The coefficient of friction is 0.10 and the pulleys are assumed to be frictionless. (b) (a) 400# 600# 30으
The friction tongs shown in Figure are used to lift a 350 kg casting. Knowing that h = 864 mm, determine the smallest allowable value of the coefficient of static friction between the casting and blocks D and D’.
A 20 kg block is held in place on an incline plane as shown by a rope that passes over a frictionless pulley at B and then over a fixed cylinder at C where the coefficient between the rope and the fixed cylinder is 0.2. Given an angle of incline, 0 = 25°, if a force of P = 200 N is applied to the end of the rope, (a) Will the block move if the coefficient of static friction between the block and the inclined surface is μ = 0.56? (b)lf impending motion exists, will the block tip or slip? Enter the magnitude of force in the rope that will cause tipping of the block as the answer in the Respondus answer-box. 0.4 m 0.8 m Ө MA 0.5 m C B P
A 20 kg block is held in place on an incline plane as shown by a rope that passes over a frictionless pulley at B and then over a fixed cylinder at C where the coefficient between the rope and the fixed cylinder is 0.2. Given an angle of incline, 0 = 25°, if a force of P = 200 N is applied to the end of the rope, (a) Will the block move if the coefficient of static friction between the block and the inclined surface is μ = 0.56? (b)lf impending motion exists, will the block tip or slip? Enter the magnitude of force in the rope that will cause tipping of the block as the answer in the Respondus answer-box. 0.4 m 0.8 m MA 0.5 m C B P
A flat belt connects pulley A, which drives a machine tool, to pulley B, which is attached to the shaft of an electric motor. The coefficients of friction are u, = 0.25 and uk = 0.20 between both pulleys and the belt. Knowing that the maximum allowable tension in the belt is 600 Ib, determine the largest torque that the belt can exert on pulley A. 8 in: 1 in.
2. A 400KN block is resting on a rough horizontal surface for which the coefficient of friction is 0.40. Which of the following most nearly gives the force P required to cause motion to impend if applied to the block downward at 30degrees with the horizontal. A. 150kN B. 160kN C. 240KN D. 300KN
3.) Uniform box A has a weight of 40 Ib, and is leaning against box B as shown. Box B has a weight of WB. Friction coefficients between the various 20 in. (friction-less) X = 24 in. Y = 10 in. 30 deg. surfaces are as shown. 24 in. W = 40 Ib u-0.7 H= 0.4 a. Draw FBD's of box A and box B. b. Determine if the system is in static equilibrium. Note – Only check for sliding of A and B. N