Answered: 10.4. What is the mean shear stress 8v…

10.4. What is the mean shear stress 8v flume 2.4 m deep and 3 m wide at the top, when the depth of uniform flow is 1.8 m? périmeter of a triangular Aume is 1 in 200 and water is flowing

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

11. A rectangular channel with width = 10 meters and depth = 3 meters has a flow slope of 0.001 and roughness n = 0.025. The flow rate is 80 m3/s. Determine the shear stress on the channel in Pascals.
1. A gravity dam with a trapezoidal section, as shown in the figure. A distance of 15 meters from the toe, a drain is located. Which point has a pressure due to uplift of zero and increasing uniformly to full hydrostatic at the heel. Upstream face 1H:5V, while downstream face is inclined 1H:2V. Determine the maximum foundation pressure EL 50m 1 1 7m EL 52m AA 9 T साझाल Drain hard EL.0 3. ar TH th re
For the cantilever type retaining structure detailed below, the water behind the wall If the level is 2.0 m below the surface, calculate the safety coefficient against slipping. Floor strength parameters c '= 0 and Φ' = 35° determined as. Ground saturated unit weight 20 kN / m3 , unit weight above the water level 17 kN / m3 , and the friction between the wall base and the floor angle δ= 25° determined as.
Check the over all stability for an earth dam with top width =8 m, height of dam=25m hw= 1.2m, u/s slope 2.5:1 H:V, D/s slope 1.5:1 H:V , the dam is provided with horizontal toe with length 11m. The submerged volume 0.44 from the full dam volume. Find the seepage value.
1. A concrete dam retaining water is show in the figure. If the specific weight of concrete is 23.5 KN/m^3. What is the factor of safety against overturning? Find the location of the resultant. Find the maximum intensity pressure. Determine the minimum intensity pressure.
Question: In a free-floor flow environment, the base width in the trapezoidal cross-section given in the figure is B=5 m, Manning coefficient n=0.014, slope slope m=1.5, flow rate through the channel Q=40 m3/s flow of flow at h=yo =2 m uniform flow depth What should be the channel base slope lo for Calculate the type of current formed in the channel and the wall shear stress in case of uniform flow. 1 Yo =2 m m 5 т
Construct a 2D flow-net for the under-seepage problem of the dam below which rests on a 2-layer foundation. Both soil layers are isotropic in Darcy's law, with the isotropic permeabilities of the upper and lower layers being 1x10 and 3x10 m/s, respectively. State and use the transfer conditions about the change of angles of flowlines (Snell's law in seepage) as flows enter and exit from layer 1 to layer 2 through their interface, and the change of flow net aspect ratios. Set ((An/As), =1) to have a 'square' flow-net in the upper region and the 'non-square' one (An/As)2-ki Ik:) in the lower layer (s being the length in the flow of flow and n being normal to it). Compute the total flow rate due to the under-seepage. 4.00m 0.50m 7 1.00 m 5.00m 10.00m- 5.00m
Water flows at flow rate Q In a rectangular canal. At height [m] 2 = h. And in width. b = 4 [m]. Manning's coefficient of roughness in the canal is. 0.015 = n Shear stress measured in channel tau = 9.81 In / m2). Next to the canal, a vertical partition was installed that divided the canal into two identical canals, the width of each canal being [m] 2 = 2/ b. A. Calculate the water level in each separate rectangular channel h h= ? b-4m B. The cross section changed to one connected rectangular channel as it was at the beginning when the water height is h = 2 [m] and width b = 4m. Add a step to the rectangular channel to create a control section (critical flow). Calculate the step height (delta (z) in the control section h=2m Az-!
A circular door having a diameter of 2.5 m closes a horizontal duct from a small dam as shown. The center of the door is 4.5 m below the dams water leve. Assuming the unit of water is 9.79 kN/m², compute the location of the center of pressure from the centroid of the door. Hinged 4.5m, CG 2.5m center of pressure
A concrete gravity dam has the following data: Maximum water level = 300.00 m Bed level = 220.00 m R.L top of dam = 304.00 m %3D The d/s slope of 0.67:1 starts at RL of 295.00 m U/s face is vertical. Center line of the drainage gallery = 8.0 m from u/s face. Consider only weight of dam, water pressure and uplift pressure. Calculate only the normal stresses at the toe and heel of the dam, assuming 100% uplift pressure at the h eel and 50% at the gallery and zero at the toe.
Q: The concrete dam shown in Figure is constructed on a soil with coefficient of permeability k = 0.06 cm/sec and ysat= 19.8 kN/m. Determine: 1- rate of flow (m/day) per meter run of the wall. 2- total head, elevation head, and pressure head at point A. 3- effective stress at point B. 4- hydraulic gradient at point D. 5- exit gradient. 6- depth of water outside the dam which cause instability at point C. 25 m 1.5 m 1= 1.2 m 8 m G.S.L XX WAY A 9 m D. 8 m B Datum AVAEN Rock
2.13 A concrete-lined rectangular channel (2 ft wide and 100 ft long) carries 200 cfs water 60°F. If the average water depth in the channel is 5 ft, determine the friction loss using the: (1) Darcy-Weisbach equation (2) Manning formula. FO 3