10.12. An LTI diserete-time system has the impulse responseh[n](0.9Y'u[n].(n) Determine whether this system is causal.(b) Determine whether this system is stable.(c) Find the system response to a unit step input xf](d) Use MATLAB to verify the results in (c) for n 0,1,2 ana(e) Repeat parts (a) through (c) foru[n].

10.12. An LTI diserete-time system has the impulse response (0.9Y"u[n]. (n) Determine whether this system is causal. (b) Determine whether this system is stable. (e) Find the system response to a unit step input xf] "[n). (d) Use MATLAB to verify the results in (c) for n 0,1,2 ana (e) Repeat parts (a) through (c) for

10.12. An LTI diserete-time system has the impulse response (0.9Y"u[n]. (n) Determine whether this system is causal. (b) Determine whether this system is stable. (e) Find the system response to a unit step input xf] "[n). (d) Use MATLAB to verify the results in (c) for n 0,1,2 ana (e) Repeat parts (a) through (c) for

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q 1: a- Compute the voltage gain Gy and then the output voltage Vout for the inverting op amp circuit shown in Figure 1, given that Vin = 1mV. Plot Vin and Vout as versus time on the same set of axes. b- Compute the voltage gain G, and then the output voltage Vout for the inverting op amp circuit shown in Figure 1, given that Vin = sin(t) mV. Plot Vn and Vt as versus time on out the same set of axes. Rin Rf 120 K2 in 20 KQ out Figure 1: inverting op-amp
16. Sketch the root locus for a unity-feedback system where Then find the following: [Section: 8.5] G (s) = K (8-2) (8-3) s(s+ 2) (8+3) a. The breakaway and break-in points b. The crossing of the jo-axis c. The range of K for closed-loop stability d. The value of K that will result in a stable system with complex conjugate poles and damping factor of 0.5
Q11 only
Control Systems
Quiq plz
Consider the integrator circuit shown below. From the input and output graphs shown, determine if this circuit is working correctly, by first determining what the output should be. (Show your working/reasoning.) The output of the integrator shown is given below: Vout Vindt RC The general form of the integral (assuming the input is a cosine) is given by: A A cos(wt)dt = – sin(wt) 100k? 0.2µF 2.2k2 Vout 300 Hz - Output = 3.13 V, PP Input 2.0 V Pp -2 -3 1. 3. 6. 8. 9. 10 Time / [ms] 2. 3. Input/Output Voltage / [V]
answer the following questions
ASAP
Given G₁ = 4(s+8) /(s+3)(s+7) and G₂=2s /(s+10) function write an m-script to determine the final transfer i. Series ii. Parallel iii. Feedback, taking G₂ as the feedback element
4. a) Find the complete solution for the difference equation y[n] – 0.9y[n-1] = x[n] with the input x[R]= (-1/4)"u[n] and initial condition y[-1]= 1. b) An LTI system has an impulse response h[n] and input x[n] displayed in Figure 2 below. (b.i) Apply the method of convolution by superposition to find and sketch the convolution output y[n] of the system. (b.ii) Determine and sketch the step response of this LTI system.
Q8 only
29 - When the unit step function is applied to the system input whose block diagram is given below, the peak time of the output response is 3.1 s, and the settlement time is 5.0 s. T and a seen in the open loop transfer function are constant numbers. What is the damping rate of the system? calculate.A) 0.54B) 0.60C) 0.62D) 0.56E) 0.58