10. Using the information shown and assuming a second order model excited by a step input, find the corresponding transfer function. Amplitude 1.6 1.4 1.2 0.8 0.6 0.4 0.2 0 System: sys Time (seconds): 0.0159 Amplitude: 1.57 0.02 System: sys Time (seconds): 0.0316 Amplitude: 0.673 0.04 System: sys Time (seconds): 0.0477 Amplitude: 1.19 Step Response 0.06 0.08 0.1 Time (seconds) 0.12 0.14 0.16 0.18

10. Using the information shown and assuming a second order model excited by a step input, find the corresponding transfer function. Amplitude 1.6 1.4 1.2 0.8 0.6 0.4 0.2 0 System: sys Time (seconds): 0.0159 Amplitude: 1.57 0.02 System: sys Time (seconds): 0.0316 Amplitude: 0.673 0.04 System: sys Time (seconds): 0.0477 Amplitude: 1.19 Step Response 0.06 0.08 0.1 Time (seconds) 0.12 0.14 0.16 0.18

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A low-pass channel with a maximum frequency of f, Hz is to be used in a communication system. Assume that the wave length for fn is 100 meters and the signal-to- noise ration (SNR) is 127 dB. (Assume speed of light to be 3x10° m/sec) a. The bandwidth of the channel is Hz b. The theoretical highest data rate for the channel is bps. c. based on the data rate in part (b), the minimum number of signal levels that can be used to represent data will be levels
An analog television signal containing frequencies up to 4.5MHz is to be coded by an ADC. The sampling frequency is 20% above the Nyquist rate. If there are 1024 quantizing levels, determine the rate of transmission.
Q2: Assume a sinusoidal signal with a frequency of 3.5 kHz and maximum amplitude of 1v. Then this signal is applied to LDM with a bit rate of 25kbps. Find the appropriate value of step size for this modulation.
Consider the following continous time signal x(t). Assume that the signal was sampled at a sampling frequency of 20 Hz. Plot the magnitude spectrum of the sampled signal as a function of cyclic frequency. Be sure to include n values of up to +-2. Label x and y axis. Did aliasing occur? If so, what is the aliased frequency? x(t) = 1 + 2cos(2pi25t)
2
Example: Suppose that an analog signal is given as x(t) = Scos (27 x 103t) and is sampled at the rate 8kHz. Sketch the spectrum for the original signal and the sampled signal from 0 to 20kHz. I need the solution step by step and clear line please
A receiver is being tested to determine SIINAD. A 400-Hz audio signal modulates a carrier that is applied to the receiver. Under these conditions, the output power is 7 mW. Next a filter is used to cancel the 400-Hz portion of the output, and then an output power of 0.18 mW is measured. Calculate SINAD. Cevap: Sonraki sayfa ar Geçiş yap.. on sy...pdf W
a) Sketch and explain the root locus curve. b) Calculate the separation point from the real axis and the gain here. c) Calculate the virtual axis cut-off points and also the gain values at this point. d) Determine and explain the stability range.
DIGITAL COMMUNICATIONS H.W. Q1/ A) Find the sampling frequency for the following signals: 1) S1 = 20 cos(1500nt) * cos (4000nt) 2) S2 = sin (200xt. 3) S3 = sin4000nt + 5 cos(1200nt) nt B) The following waveform is the RB (return to bios) representation of the serial digital data, find the digital data code and draw the NRZ (non-return to zero) and RZ (return to zero) waveforms. C) waveform below is the PAM for the analog signal, draw the analog signal, PWM and the PPM for this signal. 02/ The following data stream (10011011 11001110 11110000 10001000 11100000 11011010 11111111 01110111 10011001 11100111 01011010) will be transmitted with signaling rate equal to 80 k bit/sec. 1- Find the data transmitted using L- parity, V- parity and L&V parity. 2- Find the Hamming code of the last byte of the data only in which two error can be detected and one error can be corrected, calculate the transmitted bandwidth? how can reduce the transmitted bandwidth? Explain and calculate the reduced…
Q. Suppose that you have an angle modulaton system with an input signal £01) s wiangle wave of fundamental frequency 5 kiz and its most power is concentrated in the frst third harmonics, the masimum and minimu voltage ae | and -1 espectively. where one period equation of theinput s o[BIl 0
‏In case of the amplitude modulation of an information signal A)the modulated signal has a single frequency which is the carrier frequency . B)the modulated signal has three components with the frequencies fc , fc + fm and fc - fm C). the modulated signal has a single frequency which is fm . D)none of the other answers is correct
Please.. The sub-parts to be solved.