10. If the maximum value of the current is 5√2 A, what will be the value of the average current?

Q: Ch27 part HW. In the Figure, what is the current in each resistance? 2.00 2 24.0 V 4.00 2 3.00 2…

A:

Q: What is the value of R1, R2, R3

A:

Q: Ammeter reads 2.00A in the following circuit. What is the emf e? 700n 200 0

A: Given circuit, Ammeter reads 2 A.

Q: If the applied voltage across a series RL circuit is 120V and the voltage across the resistor is…

A: The power factor can be calculated by using the power triangle or voltage triangle.

Q: Difference between KVL and KCL

A:

Q: Q) The clamp on ammeter is used to measure an alternating current. * F

A: Given The clamp on ammeter is used to measure an alternating current.  True or false

Q: The ratio of % reactance at rated kVA to the % reactance at base kVA is equal to

A: We need to tell the correct option for the given blank in the given statement.

Q: The voltage across a 10µF is shown in the figure below. Determine the current waveform. Show all…

A:

Q: The voltage across a 10µF is shown in the figure below. Determine the current waveform. Show all…

A: The capacitor stores energy in itself in form of voltage. The capacitor opposes any change in…

Q: Where Can I Input the nodes in KVL in a Electrical Circuit Diagram

A: Given: here we assume an random close electrical circuit Calculation: Point out an node in…

Q: 1H 2H epece 0.5 H 2H Question: Detenmine tue cauivalent inductamce of he cincuit Show in above…

A: For the given Circuit with inductances, Equivalent inductance of the circuit is determine as shown…

Q: What is the expected voltage drop across each load in this circuit? #doodle 6 V and 6 V 0.01 V and…

A:

Q: Determine the output voltage waveform of the circuit.

A: Given data: The given circuit diagram is of half wave rectifier.

Q: What is the circuit time constant? I kQ i(1) 1 mH ll

A: Given circuit,

Q: For the waveform of Figure 6 below, calculate the period of the waveform: 120 Vp OV- Vertleal…

A:

Q: 0 72 T t V₂ W R +

A: In this given problem , we need to draw output voltage waveform. Circuit:

Q: Q) The clamp on ammeter is used to measure an alternating current. * T 2 F

A: Given  The clamp on ammeter is used to measure an alternating current True or false

Q: Calculate the value of the resistor(R) that must be connected in parallel with a nine μF…

A:

Q: Ammeter reads 2.00 A in the following circuit. What is the emf ɛ? 15.0 V 7.00 N 5.00 N 2.00 N

A: The given circuit is shown below, The current passing through ammeter I1+I2=2.00A

Q: How much is the % power saving if R33 was used at m=0.8

A: we need to determine power saving for m = 0.8.

Q: 10 V 60 Hz 100 µF

A:

Q: Q1] find the voltage of the inductance 1H if the value of the source is: 50 sin( 100|t) volt R3 R2…

A: Given figure,

Q: The hot steam from the turbine is converted in to water in

A: The hot stream from turbine is converted in to water in condenser

Q: (3) 7.30 8 37-j20 2750 a) if the capacitor is 10uf what is w? b) find the power burned in each…

A:

Q: 0.047 µF 11 k2 Determine the circuit. Find the frequecncy of oscillation and value of R1 need to…

A: The feedback circuit give a part of output signal back to input signal. When output signal is…

Q: 30 Ω ww 25 Q 10Ω 20 Ω а о ww ww 5Ω 15Ω bo

A:

Q: Three coils each having resistance of 25 n are connected in star across 415 V, 50 Hz supply. Then…

A:

Q: When a direct voltage of 90 V is applied to a coil, 15 A direct current flows from the source. When…

A:

Q: 2 shows a transistor circuit with pr and the value of IB(min) necessa m value of VIN that is…

A:

Q: Find R and the frequency of operation [rad/sec] for the circuit below: 100KO 5ΚΩ Vo 0.01 10 1KO µF…

A:

Q: Three coils each having resistance of 17 Q are connected in star across 415 V, 50 Hz supply. Then…

A: The power consumed in a 3 phase circuit is  P=3Vl2R=3Il2.R Vl = 440 volt R=17 ohm

Q: m the figure below choose the ect answer

A:

Q: RL series circuit is connected to 120 v,60Hz line. The inductor has voltage drop of 54 volts. What…

A:

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.