10. Apply what you learned from the class consensus model to the model of the engine below to explain whether or not a reaction must release heat to make a car go. 中

Q: A piston-cylinder device contains 1.5 kg of steam at 300°C and 0.4 MPa. Steam is cooled at constant…

A: The initial conditions are: The specific volume of the steam can be determined from the steam table…

Q: How much will an air leak cost during three monthes? the hole has a diameter 6.35mm at line pressure…

A: Given  Hole diameter D=6.35 mm Line Pressure P= 690 kPa Electricity Cost  C=7  centskwh Time of air…

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: Determine the y_bar coordinate of the composite shape. Treat the bent corners as square and ignore…

A:

Q: D Question 2 Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your…

A: Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your paper and…

Q: 7.30 5.90 4.50 Stress Lev 3.10 1.70 pox ഇന്നും 00 O 00 DO O XXOOD O OD 0 DOO 0 0 0 Оф COX0000000…

A: The intercept is calculated as the value of stress level at zero percentage From the given figure it…

Q: Question 18 Simplify (−4 − 4j) O 1.412-45° O 1.41/225° O 1.414-225° O 1.41/45°

A: Simply the above expression

Q: Find the value of x5 in 3 decimal places (positive value) using Secant Method (5th Iteration) f (x)…

A: Write the given equation. fx=sinx-x take x0=0, then  f0=sin0-0=0 take x1=1, then f1=sin1-1=-0.1585

Q: A pneumatic system operating at 85 psi comprises a series of pneumatic actuators which consume 2.4…

A: Original CFM = 2.4 CFMOriginal pressure= 85 psiNew pressure= 120 psiAtmospheric pressure= 14.7 psi

Q: QUESTION I ) Sute True or False for the following statements: O The principal stresses represent the…

A: Disclaimer: Since you have asked multiple questions we will solve the first one for you. If you want…

Q: The coal consumption per hour is the ratio of heat of combustion and calorific value.

A: True

Q: Draw chalk diagram of all sections

A: To draw section views

Q: 11 .625 .125 SECTION A-A VIEW B-B .344 1.000 .313- 0.2407+.0013 -.0013 10 .125 8 B A Q 3.875 NO…

A: Given: Name these lines.

Q: ood day. I am trying to review for examinations and require assistance for these questions... Horse…

A: Given

Q: A hydro-electric dam uses turbines to generate electricity as reservoir over the turbine blades. A…

A: (a) To fill: The blanks of the statement with appropriate choice. Explanation: Hydroelectric dam: A…

Q: FIGURE 1 60 kN B 0.75 E F :1.00 1.00. 1.00 25 kN

A:

Q: Determine ly and ky.

A:

Q: RIS R12 frant sew R32

A: Given 3D model To find Three views

Q: Question attached

A: (a) Relative humidity is the ratio of the partial pressure of water vapour in the mixture to the…

Q: The tank contains water and immiscible bil with S=0.70. What is h in cm? h 6 cm 12 cm Oil Water

A:

Q: Round number to three significant figures. 1.548937 x 10^7

A: For scientific notations significant digits/figures are calculated only for the coefficient or…

Q: a. The required gap so that the rails just touch one another when the temperature is increase p.…

A:

Q: In a hot water heating

A:

Q: tan 0 2. lim 8 -0 sin 20

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: Which best represents the Slope-field and streamlines for dy = y? – 9 dt

A:

Q: The specific weight of material is

A: OPTION C is the correct answer

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: 150 m 50 mm 85 mm Section X-X 20 kN

A:

Q: Which of the following statements below are incorrect? select all which apply.     A shear force…

A: It is needed to provide the wrong or incorrect statements.

Q: Round number to three significant figures. 0.000045389

A: Given data: The given number is N = 0.000045389. Here, there are a total of 5 significant figures.…

Q: 50 mm 150 mm 50 mm 85 mm Section X-X 20 kN

A: Let us shift the load to section X-X. The moment M and force P will create the same effect.

Q: If a turbulent water flows inside the piping system, the vertical distance h=30 mm, what is the…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.