10. A typical ceiling of a house consists of the items in the accompanying table. Assume aninside room temperature of 70°F and an attic air temperature of 15°F, with an exposed areaof 1000 ft?. Determine the temperature distribution through the ceiling. Also calculate heatloss through the ceiling.ab bood ta bon odi of(s) 1.2.3.4.Problem 11.13ResistanceItems(h • f² • °F/Btu)1. Inside attic film resistance2. Insulation batt (6 in.)0.6819.03. Gypsum wallboard (1/2 in.)4. Inside film resistance (winter)0.450.68

Answered: Image /qna-images/answer/4f0e9b6c-3983-4af4-aa62-b38061fe7d61.jpg

10. A typical ceiling of a house consists of the items in the accompanying table. Assume inside room temperature of 70°F and an attic air temperature of 15°F, with an exposed a of 1000 ft?. Determine the temperature distribution through the ceiling. Also calculate h loss through the ceiling. ab be tn bo di

10. A typical ceiling of a house consists of the items in the accompanying table. Assume inside room temperature of 70°F and an attic air temperature of 15°F, with an exposed a of 1000 ft?. Determine the temperature distribution through the ceiling. Also calculate h loss through the ceiling. ab be tn bo di

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

During daytime, the outside air temperature is measured at Ta = 35 °C. A house with an inside temperature of Tin = 20 °C is separated from the outside by a brick wall as shown in Figure 1. i Briefly discuss what will happen in terms of heat transfer process and the mode of heat transfer involved. ii. Identify the parameters that affect the rate of heat transfer in this case T. = T = 35°C 20°C Brick wall
A solid hemisphere of radius 5 cm to be cooled in air (at 20 o C, h=10 W/m 2 .K) from 200 oC to center of 150 oC, assume following sphere properties ρ=8500kg/m3, k=20W/m.K , C=400 J/kg.Ka. List assumptions and justify selected method of solution b. How long does it take to cool the hemisphere? c. What is the temperature of the surface at end of cooling?
1) A wall section composed from the outside to inside, of concrete brick 100mm thick, an air space of 50mm, two layers of fiberglass insulation 38mm thick, concrete block 150mm thick and air space of 19mm and a gypsum board of 13mm. The exterior conditions are -20C and RH=90% while the interior conditions are 23C and RH=40%. The surface temperature from the outside to inside are shown in the figure. The permeances are: Still Air: µ = 175 ng/pa.s.m Fiber glass: M=2560 ng/pa.s.m? Concrete block: M= 200 ng/pa.s.m? Gypsum board: M= 2000 ng/pa.s.m? Concrete brick: µ = 4.55 ng/pa.s.m Determine if there is a risk of condensation, and if there is, what is the condensation rate? What would happen if a vapor barrier (M=0.2 ng/pa.s.m²) was installed on the warm side of the insulation (Surface 4). 21с 19C 16 С 12C -10 -15C -18C -19C Gyp Air Concrete Fiber Fiber Air Concrete Outdoor Indoor sum block Glass Glass brick 230 19 50 mm -20C 13 150 mm 38 mm | 38 mm 100 mm RH=90% RH=40% mm mm Surf. 1 Surf.…
Give step by step answer and. Clear
Good Day, Kindly help me with this problem, Thank you P.S. T= 30 degrees
Find the temperature profile of the rectangular plate 4m x 4m, whose temperature at the side are given below: Take delx= del y= 1 m. 100 C 75 C OC 50 C
The diagram below illustrates a simplified version of the Jet Propulsion Laboratory's 25-ft space simulator chamber. Within it, tests are run for deep space probes and their components. In this particular experiment, a sensor assembly with its housing is placed inside. The sensor-housing electronics create heat such that q=3181.0 W exits the assembly's top surface into the chamber. The chamber itself is under vacuum, and its walls are at cryogenic temperatures to simulate conditions in space. Surfaces 1 and 2 are flat. Assume they are flush. The top surface of the chamber, Surface 4, can be approximated as a perfectly insulated, flat ceiling. The exposed surface of the floor, Surface 2, is a black, donut- shaped surface. Additional surface information can be seen below, including various parameters and dimensions. Assume all surfaces are opaque and diffuse, and conditions are at steady-state. PARAMETERS & DIMENSIONS Surface 1: A = 7.07 m²; diameter d; = 3 m; &₁ = 0.5; Surface 2: A₂ =…
Ans. 0.9 m Q2/A vertical cylinder having a length of 30 cm is maintained at 100-C and exposed to room air at 15-C. Calculate the minimum diameter the cylinder can have in order to behave as a vertical flat plate. Ans. 9.01 cm
Using Ritz technique, determine the temperature distribution in the fin. T=20 °c, h=0.3 w/cm² °c, k=4 w/cm °c. Assume free end is open to the atmosphere
Sipho’s mother is making a fire in the stove inside a shack using coal. A fan is used to extract the flue gasfrom the fire via a chimney made of zinc material. The wall thickness of Chimney is L=4mm and the walltemperature of the chimney on the flue gas side is T_si=60˚C. Sipho, playing outside next to the chimneyexperiences an ambient temperature of 20˚C. The surrounding temperature is T_sur=35˚C and the emissivityis ε=0.95. Assume the convection coefficient is 20W/m2K and the chimney is grey material.Under these conditions determine the outer surface (air side) temperature T_so=? of the chimney.
Quiz: A double-pane window consists of two 3 mm thick layers of glass separated by a 12 mm wide stagnant air space. For specified indoors and outdoors temperatures. 1. Determined rate of heat loss through the window and 2. The inner surface temperature of the window. kalass = 0.78 W/m-°C and k stagnant space = 0.026, The area of the window and the individual resistances are A=(1.2 m)x (2 m) = 2.4 m² Glass Glass Stagnant space Toi= 24 h = 10 w/m?.c To2- -5 c h2 25 w/m2.c 12 mm 3 mm mm
One vessel having a carbon-steel wall of thickness 5 mm carrying saturated steam and water at 423K. The vessel is insulated with magnesia of thickness 50 mm. If the ambient air temperature is 321 K, determine the heat loss from the vessel. Given: i. thermal conductivity of carbon steel is 52 W/m.K ii. thermal conductivity of magnesia is 0.5 W/m.K iii. surface coefficient of insulation surface is 3 W/m2.K