10 m/s, 5° A 10 m/s Car B is towing car A with a 5-m cable at a constant speed of 10 m/s on an uphill grade when the brakes of car B are fully applied causing it to skid to a stop. Car A, whose driver had not observed that car B was slowing down, then strikes the rear of car B. Neglecting air resistance and rolling resistance and assuming a coefficient of kinetic friction of 0.9, determine the speed of car A just before the collision. VA = 9.09 m/s

10 m/s, 5° A 10 m/s Car B is towing car A with a 5-m cable at a constant speed of 10 m/s on an uphill grade when the brakes of car B are fully applied causing it to skid to a stop. Car A, whose driver had not observed that car B was slowing down, then strikes the rear of car B. Neglecting air resistance and rolling resistance and assuming a coefficient of kinetic friction of 0.9, determine the speed of car A just before the collision. VA = 9.09 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A robot arm moves in the vertical plane so that the 0.14-kg cylinder P travels in a circle about point B, which is not moving. Know that arm BP starts from rest in a horizontal position and that the speed of Pincreases at a constant rate of 200 mm/s². 0.8 m Draw the free-body diagram of the cylinder P that is required to determine the force acting on the cylinder. (You must provide an answer before moving on to the next part.) 0.8 m P 1 I
A 74 g ball B dropped from a height ho=1.9 m reaches a height h₂= 0.25 m after bouncing twice from identical 250-g plates. Plate A rests directly on hard ground, while plate Crests on a foam-rubber mat. ho B hy Determine the height h1 of the ball's first bounce. The height h1 of the ball's first bounce is m.
The carnival ride from Prob. 12.51 is modified so that the 80-kg riders can move up and down the inclined wall as the speed of the ride increases. Assuming that the friction between the wall and the carriage is negligible, determine the position h of the rider if the speed v0 = 13 m/s.Reference to Problem 12.51:
Q6: The 2.5-Mg pickup truck is towing the 1.5-Mg car using a cable as shown. If the car is initially at rest and the truck is coasting with a velocity of 30 km/h when the cable is slack, determine: 1. The common velocity of the truck and the car just after the cable becomes taut. 2. The loss of energy. [ Ans. (1) v2 = 5. 21 m/s , (2) AE = 36.6 kJ ] 30 km/h Q7:The tanker has a mass of 130 Gg. If it is originally at rest, determine its speed when t = 10s .The horizontal thrust provided by its propeller varies with time as shown in the graph. Neglect the effect of water resistance. [ Ans.: (a) v = 0. 849 m/s F (MN) F = 30(1 – e 0.1) t(s)
A 1.6-lb slider is propelled upward at A along the fixed curved bar which lies in a vertical plane. If the slider is observed to have a speed of 11.5 ft/sec as it passes position B, determine (a) the magnitude N of the force exerted by the fixed rod on the slider and (b) the rate v at which the speed of the slider is changing (positive if speeding up, negative if slowing down). Assume that friction is negligible. 23 2.9' Answers: N = i Ib v= i ft/sec2
The double pulley shown in the figure is formed by two wheels that are coupled to each other. The complete pulley (formed by the two wheels) has a mass of 15 kg and a turning radius of 110mm. Block A has a mass of 40 kg. If a force of 2 kN is applied to the tied rope of the inner pulley wheel, determine the speed of block A after 3 seconds. At the beginning, the whole system was at rest. Disregard the mass of the string and consider that the moment of inertia (kg.m²) of the complete pulley is given by IP = mko²where m is the mass of the pulley and Ko is the radiusspinning
A worker develops a tension T in the cable as he attempts to move the 48-kg cart up the 21° incline. Determine the resulting acceleration a of the cart if (a) T = 135 N and (b) T = 222 N. Neglect all friction, except that at the worker's feet. The acceleration a is positive if up the slope, negative if down the slope. 48 kg 15° Answers: 21 O (a) T = 135 N, (b) T = 222 N, a = a =
Collar A has a mass of 3 kg and is attached to a spring of constant 1200 N/m and of undeformed length equal to 0.5 m. The system is set in motion with r = 0.3 m, v0 = 2 m/s, and vr = 0. Neglecting the mass of the rod and the effect of friction, determine (a) the maximum distance between the origin and the collar, (b) the corresponding speed. (Hint: Solve the equation obtained for rby trial and error.)
6. Exercise 2.5.32 Block A is observed to be dropping down at a steady 0.9 ft/s. At what velocity must the free end of the pulley be moving? L
Pin B has a mass m and slides along the slot in the rotating arm Oc and along the slot DE which is cut in a fixed horizontal plate. Neglecting friction and knowing that rod OC rotates at the constant rate 00. draw a FBD and KD that can be used to determine the forces P and Q exerted on pin B by rod OC and the wall of slot DE , respectively.
Block A with a mass of 20 kg moves at a constant speed of 2 m/sec, while Block B with a mass of 10 kg stops it multiplies. Block B was connected to two parallel plateaus with spring coefficients k1=500 N/M and k2=1000 N/m. A after hitting Block B Block, they move together (at the same speed) by compressing the spring. Ground with blocks if friction between the Springs is omitted, the maximum amount of compression (shortening) in the Springs is approximately what are they? 2 m/ SEC ww. A в please choose one: a.1.2 mi b. None of them O c.0.19 m d.0.26 m O e.0.45 mi
Freight car A with a gross weight of 138000 lb is moving along the horizontal track in a switching yard at 3.0 mi/hr. Freight car B with a gross weight of 166000 lb and moving at 3.9 mi/hr overtakes car A and is coupled to it. Determine (a) the common velocity V of the two cars as they move together after being coupled and (b) the loss of energy |AE| due to the impact. 3.9 mi/hr Answers: (a) V = B i (b) |AE| = i 3.0 mi/hr mi/hr ft-lb