10 kN 100 mm 15 mm 10 kN

Q: Q1\ A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long,…

A:

Q: Determine the allowable weight that the assembly can handle if the cable AB has a working stress of…

A:

Q: 1. (A). A 25mm square cross-section bar of length 300mm carries an axial compressive load of 50KN.…

A: as per our guidelines I solved 1st question only

Q: The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied…

A: Stress:  When a component or a part is subjected to any external force, a resisting force will be…

Q: The 8-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an…

A: Given data: Bolt diameter, db = 8 mm Inner diameter, di = 12 mm Outer diameter, do = 20 mm Original…

Q: 1.1 A 25 mm square cross-section bar of length 300 mm carries an axial compressive load of 50 kN.…

A: Given data: lo=300 mP=50 kNE=200 GN/m2 Need to determine the stress and the change in length.

Q: The support consists of a solid red brass C83400 copper post surrounded by a 304 stainless steel…

A: Consider Pb and Ps as the load on the brass and stainless steel tube respectively. Write the…

Q: Figure 2 shows the loads supported by a steel rod (E = 200 GPa) with a diameter of 30 mm Neglecting…

A:

Q: The ball is truncated at its ends and is used to support the bearing load P. The modulus of…

A: Given:

Q: The steel bars AC and BC, each of cross-sectional area 120 mm?, are joined at C with a pin.…

A: given data- cross-sectional area A = 120 mm2 length of the bar l= 2.5 m load P = 15 kN youngs…

Q: Before the load is placed on the rigid plate, the top of the central spring is 20 mm lower than the…

A:

Q: A 20-ft-long column is made of aluminum alloy 2014-T6. If it is pinned at its top and bottom, and a…

A: Calculating the area of cross-section,

Q: The stress–strain diagram for a material can be approximated by the two line segments shown. If a…

A: Given data: Diameter of bar, d = 80 mm Length of the bar, L = 1.5 m = 1500 mm   Let, A = area of the…

Q: The rod is 200 mm long and 60 mm in diameter. If an axial load of 300 N is applied to it, determine…

A: Given data:

Q: Determine the maximum allowable load P that can be applied to member BC without causing member AB to…

A: Given data To determine the maximum allowable load P that can be applied to member BC without…

Q: The tube is made of copper and has an outer diameter of 35 mm and a wall thickness of 7 mm.…

A: This is a type of eccentric axial loading. In eccentric loading there is two of stress , one is…

Q: A C 45° B |30° D P

A:

Q: estion 3. Determine the crippling load for a T-section of dimensions 12 cm x 12 cm x 2 cm and of…

A:

Q: Determine the relative displacement of one end of the tapered plate with respect to the other end…

A: considering free body diagram of the system calculating width…

Q: The brass rod is ixed at one end and free at the other end. If the length of the rod is L = 2 m,…

A:

Q: A 100-mm long rod has a diameter of 15 mm. If an axial tensile load of 165 kN is applied, determine…

A: Given data: L=100 mmd=15 mmF=165 kNE=200 GPa Need to determine the change in length.

Q: Direct tension indicators are sometimes used instead of torque wrenches to ensure that a bolt has a…

A: Given, Contact Area = 1.5 mm2 There are six 3-mm high heads of the indicators. ∈ = 0.1 From…

Q: A steel column has a length of 5 m and is free at one end and fixed at the other end. If the…

A: Given data: Length of column is L = 5 m. Modulus of elasticity is Est = 200 GPa. Yield stress of…

Q: Q1/ The yoke-and-rod connection is subjected to the load shown below. Determine to the nearest one…

A: Given data,Normal failure stress δN=400 MPaShear failure stress δS = 240 MPaFs)N = 2 ; Fs)S =…

Q: The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied…

A: Given data: The length of rod, L = 200 mm. The diameter of rod, d = 15 mm. The young’s modulus, E =…

Q: The five-bolt connection shown must support an applied load of P-500 kN. If the average shear stress…

A:

Q: The two pieces of wood, 150mm x 200mm, are glued together along the 55° joint. Determine the maximum…

A:

Q: 3. Determine the total elongation of the composite body carrying a tensile load of 5000 N. Assume:…

A:

Q: The assembly consists of two rigid bars that are originally horizontal. They are supported by pins…

A: Draw the free body diagram of the given figure and show the forces on it as shown below:

Q: *8-24. The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is…

A: Given data: Rod length, L=200 mmRod diameter, D=15 mmAxial load, P=300 NYoungs modulus, E=2.7×103…

Q: Q1/ The yoke-and-rod connection is subjected to the load shown below. Determine to the nearest one…

A: Calculate the permissible normal stress in the rod. Here,  is the permissible normal stress in the…

Q: 8. The A-36 steel wire AB has a cross-sectional area of 10 mm² and is unstretched when 0=45.0°.…

A:

Q: A plastic rod is 200mm long and 15mm in diameter. If a tensile load of 300N is applied to it,…

A: Given data,  L= 200 mm  D= 15 mm  F= 300 N  E= 2.7 GPa  Poison ratio v= 0.4

Q: Q.1 A rod is made of wrought iron and is secured to the piston by a tapered rod and nut and to the…

A: The critical load is the maximum load without causing lateral displacement (buckling). The column…

Q: The stress–strain diagram for a material can be approximated by the two line segments shown. If a…

A:

Q: The steel bar has the original dimensions shown in the figure. If it is subjected to an axial load…

A:

Q: A bar has a length of 200 mm and cross-sectional area of 7500mm^2. Determine the modulus of…

A: Given data: The length of the bar, L = 200 mm. The cross-section area of the bar, A = 7500 mm2.…

Q: Determine the size of the bolts used to fix the bracket in place as shown in Fig 3, if it carries a…

A: Given DataP=40kNσmax=70MPa{taken}σmin=105MPa{taken}τ=50MPa{taken}

Q: The linkage is made using two A-36 steel rods, each having a circular cross section. Determine the…

A: Consider the FBD of the system at joint B given which shows the angle between the rods and the rope.

Q: A square steel bar is 50 mm on a side and 250 mm long. It is loaded by an axial tensile force of 200…

A: GIVEN DATA- SIDE OF SQUARE a=50mm L=250mm E=200GPa P=200KN POISSON RATIO=0.3 WE HAVE TO FIND…

Q: F8-13. A 100 mm long rod has a diameter of 15 mm. If an axial tensile load of 10 kN is applied to…

A: Given:Length of rod,L=100 mmdiameter of rod,d=15 mmTensile load on rod,F=10KN=10×103 NYoung's…

Q: Determine the maximum force P that can be applied to the handle so that the steel control rod AB…

A: Apply the moment equilibrium condition at the cantilevered end named as C.

Q: Determine the allowable weight that the assembly can handle if the cable AB has a working stress of…

A:

Q: Determine the maximum value of the P value such that there would be no buckling failure (A=1.3 cm²…

A: The lateral failure of an axially loaded member in compression is known as the buckling failure of…

Q: The two vertical rods attached to the light rigid bar are identical except for length. Before the…

A:

Q: Refer to the set of bars made of a material with a yield strength of 350 MPa, determine the minimum…

A:

Q: The link AB of the pliers has the cross section dimensions 3mm x 20mm, and is made of steel with…

A:

Q: Determine the thickness of a 130 mm wide uniform plate for safe continuous operation if the plate is…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.