10 C degree water flowing at a speed of 2 m / s through a pipe with a diameter of 100 mm, air at a pressure of 2 atm at 180F at a speed of 50 ft / s from a pipe with a diameter of 2 inches, a specific gravity flowing at a speed of 5 ft / s through a 2 in diameter pipe Show whether the flow regimes of the biopolymer melt with a density of 900 kg / m3 and a density of 1 Pa-s are stratified or chaotic.

Q: A volume of 1 cu. meter of water is subjected to a pressure increase of 18 MPa Compute the change in…

A:

Q: Calculate the flux of water through MF and UF membranes operating at 1 bar pressure and 298 K.…

A:

Q: The specific gravities of solids and carrier fluids of a slurry are usually known, but the specific…

A: Specific gravity is defined as the ratio of the density of solids in the slurry and the density of…

Q: A glass sphere (Rd= 2.7) 1 mm in diameter is observed to have a fall velocity of 1.25 cm/s in an oil…

A: The viscosity is a measure of the resistance of fluid to flow. It defines the friction within a…

Q: ) Dissolved oxygen (D0) is influenced by which factors?

A: he solubility of oxygen decreases with the increase of temperature. The reason being is that the…

Q: A river is traveling at a velocity of 0.06 m/s. At x = 0 km, the river has a dissolved oxygen…

A: Introduction : Biochemical oxygen demand (BOD) : BOD is a measurement of the quantity of oxygen…

Q: What volume of water is contained in one cubic meter of material if the porosity is 20% and the…

A:

Q: 1. A water sample is known to contain 300 g/m3 of casein (C8H12O3N2). Estimate the COD, BODu, and…

A: Given data: Mass of sample of casein m=300 gm/m3 Deoxygenating Constant at temperature 20°C=…

Q: if temperature of a water sample is 20C and salinity is 30 ppt, what is the max concentration of…

A:

Q: Water containing 50 mg/L of monodisperse (uniformly sized) spherical particles of diameter 100 μm…

A:

Q: 3. A liquid which is compressed in a cylinder has a volume of 1200 cm' at 1.2 MN/m² and 990 cm' at 2…

A: The proportional reduction in the material thickness under some specified conditions of improved…

Q: What is the pH of a buffer made from 0.350 mol of HBrO (Ka = 2.5 × 10⁻⁹) and 0.090 mol of KBrO in…

A:

Q: A small lake with olume m3 has a stream flowing into it with flow rate 100 m3/day and a Toluene…

A: a) The increase in discharge concentration would lead to an increase in the overall concentration of…

Q: diameter of 0.085 mm and a solid density of 2000 kg/m3 settle in a water solution. Solids have a…

A:

Q: Calculate the percent volatility of the solids given that an empty container weighs 15.7g. A sample…

A:

Q: In General Specification for Civil Engineering Works (1992 Edition), it specifies the temperature…

A: The compaction of bitumen as well as the air void content is generally governs by the temperature.

Q: Biochemical Oxygen Demand A water sample was incubated at 20 °C for 3 days and its BOD3…

A: Using formula to find ultimate BOD

Q: A porous media is overlain by water. A pressure of 100 psia is exerted o he other end of porous…

A:

Q: Due to rise in temperature, the viscosity and unit weight of percolating fluid are reduced to 70%…

A: The given data is: The reduction in viscosity=70 % The reduction in unit weight of percolating…

Q: The bulk modulus of water is 210x10 kN/m². What pressure is required to reduce the volume of water…

A:

Q: A steel sphere, 1.5 mm diameter and of mass 13./ mg, falls steadily in oil through a vertical…

A: The given data is: Diameter of sphere=1.5 mm Mass of sphere=13.7 mg The vertical distance=500 mm…

Q: Which of the following is/are true about thin walled pressure vessels? A vessel can be classified as…

A:

Q: Convert 15,14 poises to kinematic viscosity if the liquid has a specific gravity of 0.964

A:

Q: sampie pr0a SIshipup a4 results Milligram per milli- Conceni lon equivalent for the ion (mg.

A: Name of the ion concentration of the ion. (Mg/l (E.W OF CaCo3) /E.W of Species. Hardness it…

Q: Compare flow separation for a laminar versus turbulent boundary layer. Specifically, which case is…

A: Flow separation occurs when: The velocity of the wall is approximately zero or negligible or…

Q: A small lake with volume 10,000 m3 has a stream flowing into it with flow rate 100 m3/day and a…

A: a) The increase in discharge concentration will cause a slight increase in the lake concentration.…

Q: HW Q.1 The chemical analysis of formation water as follow; concentration (ppm) 14,000 12,000 lon Na…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Calculate the THOD of a 300 mg/L solution of C5H8O2N.

A: To Find :- ThOD of a 300 mg/L solution of C5H8O2N

Q: 3. Which of the following is true? a) EGL always drops in the direction of c

A: To find : Which statement is true.

Q: A laboratory test on a suspension of a solid in a liquid gave the following information: 100 mm…

A: Given, critical time = 95 min  Original height = 100 mm

Q: (b) Yield of BOD analysis at 20°C with dilution factor, p=0.1 are as tabulated in Table Q2. Table Q2…

A:

Q: Water quality indicates that the water contains Na* at 50 mg/L, K* at 30 mg/L, Ca2+ at 80 mg/L, and…

A:

Fluid Materials

In general terms, anything that flows can be termed as a fluid. In other words, a fluid is any substance that cannot resist shear forces and deforms continuously under the application of external shear forces. Fluid materials differ completely from solid materials such as metals and alloys. For instance, if we consider two infinitesimally small cross-sectional areas of fluid materials and solid materials, and apply shear forces to these elements, both the elements will undergo deformation. Upon releasing the shear force, the element of the solid materials will regain its original orientation, but the element of the fluid materials will keep on deforming continuously under the action of the shear force.