1.what is the image below does it include what type of structure and explain the evidence of the type of structure

Q: 6 Material Science and Engineering

A: The apparent stress is equal to the difference between the average stress and the functional dynamic…

Q: What is the atomic packing factor of BCC structure? a. 0.54 b. 0.96 c. 0.74 d. 0.68

A:

Q: What will be the strain energy stored in the metallic bar of cross sectional area of 2 cm² and gauge…

A: Given- Area A=2 cm2Gauge length L=10 cmStretch δ=0.002 cmLoad P=12 kN It is needed to find the…

Q: Show that a cube has the same symmetry elements as an octahedron.

A: symmetry operations are the operations which when applied to a molecule leave it unchanged. It gives…

Q: For intermediate stages to occur during the formation of complex structures, what needs to happen at…

A: The formation of complex structures typically involves several intermediate stages. Here's a general…

Q: Determine the center of mass (z coordinate) of the composite figure? 0.5 m 1.5 m 1.8 m 0.5 m 2 m 1.5…

A:

Q: For the given structure, short term elasticity modulus is 25000 MPa and structure is being loaded…

A:

Q: 3: Discuss the practical importance of Stress Technologists working in diverse engineering fields.…

A: The ratio of force per unit area is termed as stress. The ratio of change in length to original…

Q: For the given structures, determine the degree of indeterminacy. 2.

A: To determine: degree of Indeterminacy. It is given as no. Of reactions in excess to the equilibrium…

Q: An internal stress (temperature stress) will develop if a body is restrained against dimensional…

A: If the body is restrained against temperature changes then the body cannot elongate and due to this…

Q: Y describe a representative engineering stress-strain curve rendered by crystalline materials.

A:

Q: Find one incorrect statement about the stress-strain behavior of engineering materials. Yield point…

A: there are 4 statements given below(a) Yield point (or elastic limit) can be a transition between the…

Q: The rigidity modulus of a material whose E = 2 x 106 kg/cm2 and Poisson's ratio is 0.25 will be (a)…

A: Given data : Poisson's ratio (μ)=0.25Modulus of elasticity (E)=2×106  kg/cm2

Q: (1) What is the elongation for the shown s is 200 GPa a. 0.2 mm b. 0.02 mm c. 0.002 mm d. 2 mm e. 20…

A:

Q: INTRODUCTORY CONCEPTS (a) Enumerate and explain the processes in iterative design procedure for…

A:

Q: 1. Calculate the degree of indeterminancy of the structure shown below.

A: Given data in question  Truss To find out  Degree of static indeterminacy  Note Ds = degree of…

Q: An initially rectangular element of a material is deformed into the shape shown in the figure.…

A:

Q: For a 3D truss (i.e. a space truss), formed of 469 members, how many bar elements should be used for…

A: Given, 3D truss element (Space bar) In Finite element method, every 3D truss member is discritised…

Q: A,- 150 mm E,- 200 GPa 3 m A,- ? 400 mm (1) E,- 70 GPa 1.8 m (2) 0.7 m 0.3 m 1.8 m A,= 400 mm'(3) E,…

A: Using equilibrium calculate the tension in cable. Then using formula the extension can be…

Q: A body of 25OON hanging from a steel wire 10m long of cross-section 0.05cm^2, was found to elongate…

A: Stress is defined as the force applied per unit cross-sectional area. Stress,σ = Force, FArea, a…

Q: Show the typical Stress versus Strain curve for the following materials, and define the materials…

A: Polypropylene is a thermoplastic resin that has an excellent stiffness and chemical resistance, a…

Q: Determine the determinacy and stability of the following structures please show your complete…

A:

Q: QUESTION 1. a) Name the 6 families of engineering material, including relevant sub-categories (i.e.…

A: (1) Metals Key properties: Malleability, ductility and heat conductivity (2) Polymers : Key…

Q: Calculate the tensile strength in the Brazilian examination

A:

Q: For the composite body shown in Figure 3, determine the location of the centroid (7,9) relative to…

A:

Q: What is the name of the cell wall layer marked with X? Answer: Fibre axis Lumen X Middle lamella

A:

Q: Af Find the stress in each cord of the system shown in fig. below if the cross section area of each…

A:

Q: 16.5° 0.151z mm -Deformed Undeformed 0.15 mm 0.1995mm 15.3° 0.2 mm An initially rectangular element…

A:

Q: When a material is unloaded and returned to its original shape, it exhibits plastic behavior. True…

A: Plastic behaviour- This means the material deforms irreversibly and does not return to its original…

Q: 1. The main property that affects a boundary layer is a) Temperature b) Pressure c) Viscosity d)…

A:

Q: Please determine the determinacy and stability of the given structures show complete solution for…

A: To find degree of static indeterminacy

Q: Elastic Properties of Materials 6.15 A cylindrical specimen of steel having a di- O ameter of 15.2…

A:

Introduction to Engineering Design

Students are often confused with engineering and design. The term engineering design has two words with different meanings, engineering, and design. The term engineering implies applications of laws and principles of science to design and analyze physical structures and components. In civil engineering, students apply the concept of physics and chemistry to design and build structures and buildings. In engineering disciplines, the term design means determining the dimensions, loads, and associated influences on the component due to the applied loads such as stresses and deformations. The estimation of such parameters is crucial to make the component or structure foolproof.