pls answer 1.62 1.60 Two horizontal 5-kip forces are applied to pin B of the assemblyshown. Knowing that a pin of 0.8-in. diameter is used at eachconnection, determine the maximum value of the average nor-mal stress (a) in link AB, (b) in link BC.0.5 in.B1.8 in.5 kips5 kips0.5 in.A60°-1.8 in.45°Fig. P1.601.61 For the assembly and loading of Prob. 1.60, determine (a) theaverage shearing stress in the pin at C, (b) the average bearingstress at C in member BC, (c) the average bearing stress at B inmember BC.

Answered: Image /qna-images/answer/53d3a93d-c5fc-4c2e-b1e6-fa660fd8ef44.jpg

1.60 Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 0.8-in. diameter is used at each connection, determine the maximum value of the average nor- mal stress (a) in link AB, (b) in link BC. 0.5 in. B 1.8 in. 5 kips 5 kips r0.5 in. A 60° -1.8 in. 45° C Fig. P1.60 1.61 For the assembly and loading of Prob. 1.60, determine (a) the average shearing stress in the pin at C, (b) the average bearing stress at C in member BC, (c) the average bearing stress at B in

1.60 Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 0.8-in. diameter is used at each connection, determine the maximum value of the average nor- mal stress (a) in link AB, (b) in link BC. 0.5 in. B 1.8 in. 5 kips 5 kips r0.5 in. A 60° -1.8 in. 45° C Fig. P1.60 1.61 For the assembly and loading of Prob. 1.60, determine (a) the average shearing stress in the pin at C, (b) the average bearing stress at C in member BC, (c) the average bearing stress at B in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q.3 A level circuit is shown in figure. The survey, needed for local engineering project, commenced at BM 35, the elevation of new benchmarks 36, 37, 38 and 39 were determined, and then the level survey was looped back to BM 35, the point of commencement. Fined the adjusted new BMs. ВМ 35 Elevation(m) 185.000(fixed) 35 36 37 38 39 35 184.242 187.299 186.251 188.397 184.933 BM 36 0.9 km. вм 35 0.8 km OBM 37 0.8 km 0.6 km BM 39 BM 38 0.7 km
alculate volume of cut and fill, the elevation of natural ground shows on all nodes and elevation is equal to 102.5m, all dimension and elevations are in meter. 101 (2) 102.5 C 104.2 C 108.10 f 98.45 -10 m- f 100.5 (4) 102.5 C 105.7 f 97,35 f 99.80 101, 104 10 m C 104 106.5
Q2). Calculate volume of cut and fill, the elevation of natural ground shown on all nodes and design elevation is equal to 103 m, all dimension and elevations are in meter. hi h, 101 102.5 W₂ 104.2 ha 108.10 98.45 412 100.5 Wy -10 m 102.5 hey 105.7 12 97.35 99.80 101, hs 104 hi 10 m ha 104 106.5 hi Thi
3. Given the following three wire leveling notes: Station Backsight Stadia BM1 Foresight Stadia Elevation 425.00 1.152 1.117 0.935 0.899 0.718 0.662 TP1 2.784 1.904 2.420 1.537 2.057 1.172 ТР2 2.591 2.210 2.094 1.714 1.599 1.218 BM2 a. Find the difference in elevation of TP2 and BM1, b. Find the elevation of BM2
Correct answer is 9,872.198 kN. No other answer thanks
The numerical value of departure equals the difference between the X coordinates of A and B, i.e. the increment AxAB, while the numerical value of latitude equals the difference between the Y coordinates of A and B, i.e. the increment AYAB- grid azimuth The horizontal distance DAB and the AAB can be computed. Ar - Xg - XxA Ay AB = Ys - YA D - Jar, + Ay Ay Ar AB AB = arctan AB AB
Determine area using DPD Method.
Please answer 15.2
An engineer surveyor used a 100 m tape to measure the distance ABC. He started at A. He placed the first pin 1.34 m east of B with a tape length of 95 m. Then he placed the second pin 2.65 m (with full tape length) north of line BC. The last pin was placed at C. The total recorded distance was 271 m. What is the corrected total distance of ABC?
PAGE:. DATE :.. A rectangular lot steei tape which was later found to 5 mm too short. The recorded dimensions was mearured uring a be 121.5m long by 92:5m wide. What ir the Were error in the area