1.3-3 Segments AB and BC of beam ABC are pin connected a small distance to the right of joint B (see figure). Axial loads act at A and at the mid-span of AB. A concentrated moment is applied at joint B. (a) Find reactions at supports A, B, and C. (b) Find internal stress resultants N, V, and M at 4.5 m. 136 N-m at joint B 3m 220 N B C 440 N |A 6 m 3 m Pin connection PROBLEM 1.3-3

1.3-3 Segments AB and BC of beam ABC are pin connected a small distance to the right of joint B (see figure). Axial loads act at A and at the mid-span of AB. A concentrated moment is applied at joint B. (a) Find reactions at supports A, B, and C. (b) Find internal stress resultants N, V, and M at 4.5 m. 136 N-m at joint B 3m 220 N B C 440 N |A 6 m 3 m Pin connection PROBLEM 1.3-3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. Solve for the normal stresses at members CE, CH and BC in MPa if the area of each truss member is 1690mm2. 560 N 560 N 560 N -1.5 m -1.5 m 1.5 m- B 1 m 2 m E H. F
1.3-3 Segments AB and BC of beam ABC are pin connected a small distance to the right of joint B (see figure). Axial loads act at A and at the mid-span of AB. A concentrated moment is applied at joint B. (a) Find reactions at supports A, B, and C. (b) Find internal stress resultants N, V, and M at 4.5 m. 136 N-m at joint B 3m 220 N 440 N 6 m 3 m Pin connection
Problem 6.93 The cross section is rectangular with a base of 5 in. and height of 8 in. A force of P = 20 kip is acting on the beam. -4.5 ft P -4.5 ft- -3 ft- B Part A Determine the absolute maximum bending stress in the beam, assuming that the support at B exerts a uniformly distributed reaction on the beam.
Frame ACGE is on hinge support at Aand E and braced at B and F to resistforce T = 18kN.a = 2 mb = 1 mc = 1 ma. Find the reaction at D in kN. b. Find the stress in brace BD if it ismade of pipe of ø = 75 mm andthickness = 6 mm. c. If brace AB is connected to BDconsist of two flat bars bolted topost AC at B using 20-mm-ø bolt,find the average shear stress (inMPa) in the bolt.
1.3-4 Segments AB and BCD of beam ABCD are pin connected at x = 4 m. The beam is supported by a sliding support at A and roller supports at C and D (see figure). A triangularly distributed load with peak intensity of 80 N/m acts on BC. A concentrated moment is applied at joint D. (a) Find reactions at supports A, C, and D. (b) Find internal stress resultants N, V, and M at x = 5 m. (c) Repeat parts (a) and (b) for the case of the roller support at C replaced by a linear spring of stiff- ness k, 200 kN/m (see figure). 80 N/m 200 N-m at joint D A D 4 m B\ 4 m ; 3 m Pin connection Part (c) PROBLEM 1.3-4
Home Work// The beam is supported by a pin at A and a short link BC. If P = 15 kN, determine the average shear stress developed in the pins at A, B, and C. All pins are in double shear as shown, and each has a diameter of 18 mm. 4P 4P 2P 0.5 m 0.5 m m--1.5 m--15 m- 30
1.3-4 Segments AB and BCD of beam ABCD are pin connected at x = 4 m. The beam is supported by a sliding support at A and roller supports at C and D (see figure). A triangularly distributed load with peak intensity of 80 N/m acts on BC. A concentrated moment is applied at joint D. (a) Find reactions at supports A, C, and D. (b) Find internal stress resultants N, V, and M at X = 5 m. (c) Repeat parts (a) and (b) for the case of the roller support at C replaced by a linear spring of stiff- ness ky = 200 kN/m (see figure). 80 N/m 200 N-m at joint D A 4 m B 4 m 3 m Part (c) Pin connection
The steel truss was subjected to horizontal force 2kN at C. Find the member forces of AC using the method of virtual work. 2.4m B 2KN 1.8m A 10. The force at member AC is in O a. Tension b. Compression O c. Zero O d. None of the above
4. Select member FC and CB in the truss to carry the inclined force P. Set the allowable tensile stress at 150 MPa. F A C B 6 equal spaces at 6m = 36m 800 kN 3 E 9 m 9 m
If the load P on the beam below causes the end C to be displaced 10mm downward, determine the normal strain in wires CE and BD. D 4 m A. B 3 m 2 m 2 m
Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P at A. Diameter of wire CD is 1/8 of an inch and the diameter of the pin at B is 1/8 of an inch. Determine the tensile stress in wire CD and the direct shear stress in the pin at B. dw C 4 in. dp B 15° 5 in: View a-a of B P = 200 lb.
CE - PC 311 - STRUCTURAL THEORY Plate No. 10 - Analysis of Statically Indeterm in ate Beam s 1. By the moment-area m e thod c a lc u la te th e slopes of the e la stic curve at A, B and C and the vertic al de fle ctio n at C of the sim p le beam. E = 30,00 0 k/in and I = 300 in *. 2 Refer to th e fig ure b e lo w. AIl decim a ls m ust be inclu ded, do not round o ff answers. A Il figures must be in c luded and drawn straight. Curves may be done freehand. Sum marize your ans wers as shown below. Required V a lu es Answer B A X 1 X 2 X 1 X 2 kip ft ft 15.8 5 15 B.