1.2 Which of the following gives the moment of force P about point C?A. Prcos(θ), clockwiseB. Prcos(θ), counterclockwiseC. Pr, clockwiseD. Pr, counterclockwise For nos. 1-4, Consider rod ABC bent in the shape of an arc of circle of radius, r. Knowingthat 0=60°, answer the following:B

Answered: Image /qna-images/answer/aa77270d-d152-4777-a17d-7971386f375c.jpg

Answered: 1.2 Which of the following gives the…

1.2 Which of the following gives the moment of force P about point C? A. Prcos(θ), clockwise B. Prcos(θ), counterclockwise C. Pr, clockwise D. Pr, counterclockwise

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.21P: Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10...

See similar textbooks

Related questions

Q: Problem 1: Calculate the forces in the required members of the truss shown: F1 F2 F3 H G F k.A F4 В…

Q: 12 mm PROBLEM 1.9 Two horizontal 22 kN forces are applied to pin B of the assembly shown. Knowing…

A: Given: Two horizontal forces of 22 KN acting on upper joint of the link. The free body diagram will…

Q: Required: DO NOT INCLUDE ANY SIGN By = kN use 2 decimal places Bx = kN use 2 decimal places Су 3 kN…

Q: a) What is the required tube length for these conditions? b) To design a water heating system,…

A: First we will evaluate the reynolds number then the nusselt number then the heat transfer coeff…

Q: Question 2 a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial…

Q: 75 kg E=0.3 15 eg 41,2m 25 kg |2.0m

A: given; →mass of C (mc)=75kg→coefficient of friction (μ)=0.3→mass of B (mB)=15kg→when start from B;→…

Q: Review Part A - Transmitted power A solid circular rod is used to transmit power from a motor to a…

Q: In Basic Occupational Safety and Helth Describe the Chain Reaction that is triggered when fire…

A: Given question: Describe the Chain Reaction that is triggered when fire has started.

Q: The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32 mm…

A: Find , Mean effective pressure Indicated Power

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

Q: The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load:…

Q: b) Figure Q2b shows a solid and homogeneous section, where (31.25 mm, 41.54 mm) are its centroid…

Q: A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of…

Q: 2. The satellite traveling on a acceleration of the airplane in terms of b, e, e, A dish below…

Q: A horizontal belt conveyor arranged as shown in the figure P1 below operates at a speed of 270 fpm…

A: When an amount of force act on the object, it has the tendecy to rotate the object about an axix…

Q: Determine the coordinates of the centroid of the shaded area. 1.7" 2.2" 5.4"- Answers:

A: To determine the centroid of the composite area.

Q: The uniform 7.3-m pole has a mass of 195 kg and is supported as shown. Calculate the force P…

A: Given Mass of pole, m = 195 kg Coefficient of friction = 0.39 Length of the pole, L =…

Q: Provide a complete given and computation. Include all the decimals. In an ideal reheat-regenerative…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: 2. Determine the force in each member of the truss in Fig. Q2 and state if the members are in…

Q: A cylinder is moving a 6000 lb load up a 20° slope as shown in the figure below. The friction…

A: Given: Angle of inclination→θ=20° Friction coefficient between the surfaces→μ=0.4 Mass of the…

Q: expression for R in terms of unit vector notation). (c) determine the magnitude and direction of the…

Q: It is an approximation of a force applied over a very small area. It is a slender bar that carries…

A: A point Load is an approximation of a force applied over a very small area

Q: b) For the truss structure in Figure Q4, determine the forces FAE, FAB and FCF acting in members AE,…

Q: The bulldozers exerts a force F = 60i kN at A. What are the tensions in cable AB, AC and AD? Given…

A: Find tension in AB , BC,AD

Q: 9. How many times does this object STOP moving? 40 30 20 10 20 40 60 80 100 Time (s) () aoue

A: Answer: the object stops for 1 time (20-40s)

Q: The force Pis applied to the 36-kg block when it is at rest. Determine the magnitude and direction…

Q: Problem 1: Calculate the forces in the required members of the truss shown: F1 F2 F3 H F h F4 C D E…

Q: Water flows at 1 kg/s in a 10 mm diameter tube and is to be heated from 25 to 75 °C. The tube…

A: INTRODUCTION : When a flowing fluid travels through a heat exchanger, our focus is on either cooling…

Q: An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which fails when the…

Q: 3. 130 Consider a Rankine cycle with reheat as shown in the diagram, with state properties as…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: Figure Q3a shows a simply supported beam AB with support reactions RA and RB. Two point loads F1 =…

A: In order to calculate the external reactions, first of all we have to use the equilibrium equations…

Q: The car shown in the figure below has a mass of 1878 kg. The coefficient of static friction between…

Q: cylinder neter is used to measure the viscosity of fluids. The viscometer we are using has an inner…

Q: Determine the chain speed in meter/sec of an rc 80 on a 21-tooth sprocket turning at 600 rpm.

A: find the speed of chain.

Q: A beam is loaded as shown in the figure. F = 2000 Ib, b = 3 in. and h = 6 in. F 3 ft 9 ft b h 12 ft…

A: Answer: (a) The maximum shear force in the beam is 1500 lb. (b) The maximum bending stress in the…

Q: Disk A (ma=8kg) which is initially moving with vAI= 20m/s towards right undertakes a central impact…

Q: A circular plate 3 m diameter is Immersed in water in such a way that its greatest and least depth…

A: We know that a circular plate with a diameter of 3 m is immersed in water with a maximum depth of 4…

Q: The pulley system shown in Figure Q1c lifts a mass,m,of 550 kg.Calculate the force FA necessary to…

Q: Kinetically how many degrees of freedom are required to model the system shown in Figure (7)? Also,…

Q: For fc' above 28 Mpa, Beta1 shall be reduced linearly at a rate of 0.05 for each ____ 7 psi 1000…

A: Correct answer: (b) 1000 psi

Q: ericsson cycle with air as the working fluid in a steady-flow system is at 27C and 120kPa at the…

Q: PROBLEM 2: Calculate the components of the forces at B and C. A

Q: In a gas turbine, air at 15°C is compressed from 1.01 bar with a pressure ratio of 6/1. Afterward,…

Q: The diagram in figure mm diameter to a very large tank where the free water surface is assumed to…

Q: y b d'e

Q: the blanks: the center distance in (cm) of 4 direct contact rolling.cylinders. Cylinders A-D have a…

Q: Determine the pressure difference between pipe A and B for arrangement shown in Fig. P. 1.13.20. 0.2…

Q: d pipe assuming laminar flow, be more or less if the fluid were more viscous, but the pressure…

Q: 11. What is the total distance that the object travels?

A: Displacement can be understand as the minimum distance between the initial and final position.…

Q: 3. A 2-mm-diameter and 10-m-long electric wire is tightly wrapped with a 1-mm-thick plastic cover…

Question

100%

1.2 Which of the following gives the moment of force P about point C?

A. Prcos(θ), clockwise

B. Prcos(θ), counterclockwise

C. Pr, clockwise

D. Pr, counterclockwise

For nos. 1-4, Consider rod ABC bent in the shape of an arc of circle of radius, r. Knowing
that 0=60°, answer the following:
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A force F of 40000 lbf is applied to rod AC the negative Y-direction. The rod is 1000 inches tall. A Force P of 25 lbf is applied in the negative Z- direction at point E, and a force R of 75 lbf is applied in the negative Z-direction at point F. Rod AC has a diameter of 1 inch from A to C, a diameter of 1.5 inches from B to C, and all fillet radii are 0.25 in. The rod is made of 1020 CD steel, and has a Sy of 135 ksi, a Sut of 150 ksi, and an ɛf = 0.15. Determine the effective stress at point B. 100 100 200 F. 800 B. 100 2D view of rod AC in XY plane
A The reaction in the x-direction at joint A in Figure is: O-5.774 KN 5.774 KN O 5.0 kN 5 KN OOKN E 30" 30" F 10 kN D B ALL DIMENSIONS IN METRES (0.5774) (0.5774)
A square plate with sides 1.5 m in length can rotate around an axle passing through its center of mass (CM) and perpendicular to its surface (see figure below). There are four forces acting on the plate at different points. The rotational inertia of the plate is 16 kg - m². Use the values given in the figure to answer the following questions. (Assume 0 = 40°. Express your answers in vector form.) 30.0 N 60.0 N CM 20.0 N 40.0 N (a) What is the net torque acting on the plate?
The rod made of two different materials is fixed at point A. AB aluminum, BC steel It is made of materials. E1 = 70 Gpa and E2 = 210 Gpa. P = 100 kN axial compressive force It affects the C point. The diameter of the circular bars is D1 = 80 mm, D2 = 40 mm and their length L1 = 20 cm. and L2 = 30 cm. (The direction of the force P is in the negative x-axis direction.) a) What are the displacements at B and C points? b) What is the reaction force at point A? c) What are the stresses in the bar?
The following diagram corresponds to questions 1 to 3. A beam rests on two sharp edges as shown on the image. The beam has a length of 7,50 m and a mass of 4,25 kg. Object 1 has a mass of 1,50 kg; object 2 has a mass of 2,35 kg. Point P is 0,50 m form the center of the beam. d 2 Pl CG 1. How much is the torque done by object 1 around point P? A. 55,2 N*m B. 7,36 N*m С. 62,5 N*m D. Object 1 doesn't exert a torque.
The answer must be wn= sqrt(3g/5b). Solve this without the application of Moments please.
Pii The dimenstons of the various links of a freumabre riveter, as shown in hy Q-V , { OA = 175mm, AB- 180 mm, AD = 500 mm, and BC= 325mm Find the velo city rettio betuem) C and ram D when OB is verheal, (Ans= 医:L4) 45 A
The weight of the linkage AB =BC= 20KG .Find the force acts on bar BC -875 mm- B 400 625 mm 30 60 F = 800 N
An L-shaped bracket is supported by a frictionless pin at A and a cable between points B and D. If pin A is the origin, point C is at (-7, 0); and pin B is at (-7, -10). The cable is attached between point B and an anchor at point D, at (-2, -14). Units are in feet. Force F acts at point C at an angle of 60o from the positive x-axis. Determine the magnitude of the moment that the force F produces about point A. Determine the tension required to hold the bracket in position.
Solve the preceding problem for the element shown in the figure.
A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo is unloaded by a container handling crane. Each bollard is fastened to the wharf using anchor bolts. Three cables having known tension force magnitudes F, = ll0 kN.F, = 85kN.and F, 9OkNare secured to one bollard at a point A with coordinates (0.0.45 m. 0) in the x-r-: coordinate system shown in the figure part b. Each cable force is directed at an attachment point on the ship. Force F, is directed from point A to a point on the ship having coordinates (3 m, 9 m. 0) force F, is directed at a point with coordinates (6.5 m. 8.5 m. 2 m) and force F, is directed at a point with coordinates (8 m. 9 m. S m). The diameter of each anchor bolts is 4 24 mm. (a) Find the reaction forces and reaction moments at the base of the bollard. (b) Calculate the average shear stress in the anchor bolts (in the x-: plane). Assume each bolt cart ics an equal share of the total force.
L3 =440 B M1 IC M2 L4 = 510 M1= 81 M2-48 L3 (mm) L4 (mm) 80 mm 120 mm а-а -b-b Geometric situation in figure 4, which consists of small dimensions in figure 4 The system is made of steel structure and is under the influence of torsional moments. your rod angle AB 80mm; Angle BC is 120 mm and the sliding unit of the steel G= 80000 MPa. a- Draw the torsional moment diagram of the rod. b- Calculate the maximum shear stress that will develop in the system. C- Calculate the relative rotational value of point C with respect to point A.