1.1 A simply supported beam with span of 6 m carry a dead load of 15kN/m and live load of 10kN/m. Find the total maximum deflection, consider that 30% of live load are sustained.f' = 20.7MPa 500 300 3-28 70

1.1 A simply supported beam with span of 6 m carry a dead load of 15kN/m and live load of 10kN/m. Find the total maximum deflection, consider that 30% of live load are sustained.f' = 20.7MPa 500 300 3-28 70

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: An 18-ft beam is supported by a pin and a roller at x = 0 and at x = 12 ft, respectively. The beam…

A: Find deflection at right end

Q: 10-1 A simple beam AB supports five equally spaced loads P (see figure). Using superposition method,…

Q: Pb- 7 A 20 mm diameter bar is 1.25 m long. When the bar is simply supported at its ends in a…

A: Given data- Length of bar, L = 1.25 m, Diameter of bar, d = 20 mm, Concentrated load, W = 370 N,…

Q: Compute the value of the following for the beam shown: (EI is constant.) a. Slope A b. Deflection Ap…

Q: (a) the deflection VA of the beam at A, and (b) the deflection Vmidspan of the beam at midspan…

Q: PROBLEM 2: The trapezoidal loading is carried by the simply supported beam AB. The beam is a steel…

A: Given:Required:Slope at A and deflection at midspanNote: As per bartleby guidelines, only first…

Q: Strictly show all of the free body diagrams used upon solving the problem. Complete solution is a…

A: Given, The above beam is a simply supported having a length of 6m and is loaded with Point load and…

Q: Solve for the Maximum Deflection (Propped Cantilever Beam with Point Load and UDL)

Q: A reinforced concrete beam is 300mm wide and 500mm deep. The beam is cantilever over a span of 3m…

A: b = 300 mm d = 500 mm L = 3 m DL = 10 kN/m LL = 5 kN/m

Q: A simply supported beam is loaded by a couple M at its right end. Determine the maximum deflection…

Q: DETERMINE THE DEFLECTION REQUIRED IN EACH OF THE FOLLOWING STRUCTURES. USE ONLY ONE METHOD TO SOLVE…

A: Given: E=200 GPaI=800×106 mm4 To find: Deflection at left end of the beam. Method used: Double…

Q: ding shown, use discontinuity functions to compute (a) the slope of the beam at B and (b) the de…

Q: Problem 4 For the beam shown below, find the value of EIY at 2m from R2. E= 18500MPa and; beam cross…

Q: For the simply supported beam shown, compute (a) the slope and deflection at midspan, (b) the…

A: Given a simply supported beam carrying UDL. It is required to calculate the slope and deflection at…

Q: 5-Determine the deflection at the center of the structural A992 beam shown below. Assume the area…

A: I = 68.9 in.4 A992 beam Determine the deflection at the center of the beam.

Q: The maximum deflection in simply supported beam of span 10 m subjected to a central point load of…

A: Given data : Length (L)=10 m Load (W)=100 KN EI=104 KN×m2

Q: A 10 m beam is simply supported at the right end and is fixed at the left end. It is subjected to a…

Q: Example 10.2 A rectangular cantilever beam of span 4 m is 35 cm x 65 cm in cross-section. Bending…

Q: 2. Compute for the reaction at the center so that there will be no deflection at the center of the…

Q: Compute the immediate deflections due to dead load and live load on the beam of the figure for…

A: We’ll answer the first question(In -Pound unit) since the exact one wasn’t specified. Please submit…

Q: A beam 300mm x 600mm has a steel area of 3321mm2 at the bottom with steel covering of 75mm. Use: f’c…

A: Design procedure of the beam: Geometrical properties of the beam. Loads on the beam. Calculate the…

Q: For a simply supported beam of span 5 m carrying a uniformly distributed load of 6kN/m over the…

A: Given data Simply supported beam UDL Span length

Q: A wide flange beam with dimension of: bf = 400 d = 500 tw = 12 tf = 18mm is subjected to a V =…

A: Solution:

Q: Problem 2: AKYm Calculate for the Maximum Deflection of the given Propped Beam in mm. om im C E =…

A: As per our policy, the solution of first question is provided, for the solution of second question…

Q: Derive the following equation of maximum deflection using the double integration method.

A: According to guidelines we are supposed to answer only first question, please post other questions…

Q: Q.3/ A three-span continuous beam ABCD is simply supported at A and D and loaded as shown in Fig. if…

Q: Using Moment Area Method, determine the deflection at the point of application of the concentrated…

Q: An overhang beam of uniform El is loaded as shown in the figure below. The deflection at the free…

Q: Q.3/A three-span continuous beam ABCD is simply supported at A and D and loaded as shown in Fig. if…

Q: A 10 m beam is simply supported at the right end and is fixed at the left end. It is subjected to a…

A: step 1-

Q: D A, O ( PLA3)/48EI O (PL^3)/48EI O (PL^2)/16EI O (-PL^2)/16EI P.

Q: Solve for the deflection at the middle/midspan of beam (a) below. Assume the beam is 6 k/ft Type…

A: We have to solve question a only as asked.We have to find the deflection at middle span of beam

Q: For a smple supported beam shown below EI P 2E1 P EL B 2L L. (1) Use the method of moment-area to…

A: Using moment area method

Q: For the beam shown, determine the maximum deflection, El-1x10. 4 kN/m A — 3 m B MAJ +12% = 12X 35…

Q: Compute the value of 6g for the static analysis of the given beam with the help of the slope-…

A: Due to proper distribution, one can easily find the nature of load and amount of values which is…

Q: Determine the maximum deflection of the beam

A: Find the reactions:RA=RD=P2Moment equationiorigin=AMx=P2x 0<x<L2iiorigin=DMx=P2x…

Q: F12-10. Determine the slope and deflection at A of the cantilevered beam. E = 29(10³) ksi, I = 24.5…

Q: 102 kN/m F G L/4 8 meter

Q: Q2) cantilever beam is 4 m long and has a distributed load of 300 N/m. The flexural stiffness is 60…

Q: Q.3/ A three-span continuous beam ABCD is simply supported at A and D and loaded as shown in Fig. if…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

1.1
A simply supported beam with span of 6 m carry a dead load of 15kN/m and live load
of 10kN/m. Find the total maximum deflection, consider that 30% of live load are
sustained.f'c = 20.7MPa
500
300
3-28
+₁
70

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction and objective

VIEW

Step 2: Calculate the Moment of Inertia of transformed cracked Section

VIEW

Step 3: Instantaneous Deflection in Beam

VIEW

Step 4: Total maximum deflection

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 90 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

6.2 Determine the instantaneous and long-term deflection of the free end of a 12-ft-span cantilever beam for each of the following load conditions. Assume that only dead loads are sustained, and the dead loads No. C -8' 0"- (2.4 m) Figure 6.13 Problem 6.2. include the self-weight of the beams. Use f = 4 ksi, fy = 60 ksi, and a time limit of more than 5 years. Refer to Fig. 6.13. d (in.) h (in.) P₁ L b A' S (in.) (in.²) 12 19.5 23 8 no. 8 2 no. 8 1.6 Note h-d=2.5 in. indicates one row of bars, whereas h-d = 3.5 in. indicates two rows of bars. Concentrated loads are placed as shown. - 4' 0"- (1.2 m) As (in.²) Po WD (K/ft) Ро W₂ (K/ft) (K) 2.4 P₁ (K)
(a) A hinged beam system is loaded as shown below. Determine the slope at point E and D. Also determine the deflection at D. Use Conjugate beam method. 6 kN A D E Hinge -2 m2 m2 m B 21 6 m
Answer asap please
DETAILED COMPUTATION PLEASE.THANK YOU
A simple supported beam made up of a material with the density of 2400kg/m3 has a rectangular cross section of 200mm x 450mm. In addition to the self weight, the beam is subjected at 2/3rd of the span (from left hand) with a point load of P kN. Find out the maximum deflection and slope if the span length of the beam is 3.5 m. (Where P is equal to 55). Consider the self weight of the beam in solving the question.
Derive the following equation of maximum deflection using the double integration method. (For the type of loading 4-6).
dj
Show solution
For the beam and loading shown, (a) express the magnitude and loca-tion of the maximum deflection in terms of w0, L, E, and I. (b) Calcu-late the value of the maximum deflection, assuming that beam AB is a W18 * 50 rolled shape and that w0= 4.5 kips/ft, L= 18 ft, and E=29 *106 psi.
Problem (8.3): Derive the equation of the deflection curve for a simple beam AB loaded by a couple Mo at the left-hand support (see Figure 8.23). Also, determine the maximum deflection 8max. Mo B L
Locate the position o maximum deflection. What is the deflection at 2 meters from the left? Concentrated Load = 350N, Triangular Load = 1700N/m Dimensions: Length = 1.0(2) = 2.0mm, Thickness = 40mm, Height = 200mm, Height - Thickness = 160mm