1. Using the method of joints, calculate the force in each member of the trusses shown. State whether each member is in tension or compression. А B WANN E F P P C G

Q: Determine the gross area of steel needed to design the bar force members at BC, BE, and AE. Stress…

A: Determine the gross area of steel needed to design the bar force members at BC, BE, and AE.

Q: Determine the forces in members CD, CJ, and DJ.

A: Given:- To find:- Force in members CD, CJ and DJ Reaction at I

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: Calculate the force in each member of the loaded truss. Forces are positive if in tension, negative…

A: Tanθ = 3.6/3 θ = 50.16 Efy = 0 Ay + Cy = 0 Ay = - Cy EMA = 0 Cy X 6 + 2.7 X 3.6  = 0 Cy = - 1.62 kN…

Q: Answer the table below. The truss illustration and instruction is also below

A: Step 1: Step 2:Step 3:Step 4:

Q: Method of Joints. By method of joints, determine the bar force in all members of the truss shown in…

A: Given data in question  Load 550 kN and 330 kN Span 11 m Height 6 m To find out  Member forces using…

Q: eformation sustained by members CG, AF, 12 kips

A: Given:- 8 kips,12kips To find:- deformation sustained by members CG,AF,FG

Q: Determine which truss do not carry any tension or compression forces. The truss is subjected to a a…

A:

Q: Directions: Answer all questions. Give complete solutions and show all work including units. If…

A:

Q: Using the method of joints. Determine the force in each member of the truss shown in the figure.

A: In truss each member force from both side is equal, i.e, TAB = TBA

Q: 2. The following the truss figure, came from your Module 1. Page 9. 3 m H H C G 30 kN 70 kN 4 panels…

A:

Q: Analyze the Truss by stiffness method as shown in figure below. Take point p load equal 36 Note:…

A: given data,P=36KNtaking moment at 5 point ∈M5=0R1×2=36×4R1=72KN∈H=0R1+R5=0R5=-72KNat joint…

Q: Determine the forces in members EH and El of the double Fink truss (positive if in tension, negative…

A:

Q: Question 3. in the truss shown, a-5m, b 4m, and c=4 m Determine the force in member BE is kN. Use ve…

A:

Q: Given the truss and loading shown below, determine the stress at member FC if P₁ = 18.375 Kips and…

A:

Q: A simply supported planar truss is subjected to point loads at joint B and D as shown in Figure 2.…

A: Find the reaction of the truss calculate θ=tan-113.2710=52.99° and α=tan-113.275=69.35°consider ∑…

Q: Determine the three  forces  acting  on the plate that are equivalent  to the force R=210k KN

A:

Q: By method of section

A: Determine the force in member JK, CJ and CD using method of section.

Q: STRENGTH OF MATERIALS PLEASE WRITE THE SOLUTIONS LEGIBLY AND USE 4 DECIMAL PLACES. RATE WILL BE…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: The members of the truss shown below are made of steel (E = 200 GPa) with cross-sectional area of…

A: To determine the elongation of members of the given truss under the given loading, we can use the…

Q: Determine the gross area of steel needed to design the bar force members at BC, BE, and AE. Stress…

A:

Q: For the truss shown in Figure 2.3a, determine the force in member BH if m = 5 m, n = 6 m, a = 83°,…

A:

Q: föllowing SS is subjected to diameter mm and is subjected to double shear. Determine the average…

A: Consider the diagram as shown below.

Q: Please solve this problem with a step by step guide so I can understand!

A: By considering the symmetry of the truss: AB = DEBC = CDAH = EFBH = DFBG = DGGH = GF

Q: The tension AB in the truss as shown in the figure below, is 100 N .Fill the following blanks: 2 m D…

A:

Q: E D H G 4 ft-4 ft- 3000 lb 1000 lb B K

A:

Q: own below is 500 mm². 4. 3 m 3 m 3 m Determine the load P that will not (ceed a stress of 100 MPa in…

A: First find the reactions at the supports  And then find the internal force in each member using…

Q: Design a square column to carry the working load of 1200 kN

A: given-  a square column carrying load of 1200KN grade of steel=500 grade of concrete=M20

Q: Q2: Determine the force in members JK, JN, and CD. State if the members are in tension of…

A: A truss is given as shown in the figure above and it has been asked in the question to determine the…

Q: 3. The cantilever truss is loaded as shown in the figure; determine the force in members BD, CE and…

A: Consider the figure.

Q: Using the method of joints, determine the force in each member of the truss shown. State whether…

A: Answer Let us first draw the free body diagram of forces acting on the given truss as shown below…

Q: 500 D E 250

A: We will use method of section and method of of joints to solve this question

Q: (a). Indicate whether the members are in Example 26: Determine the force in members GE, GC, and BC…

A:

Q: The members of the truss shown below have a cross- sectional area of 10,000 mm2. Determine the…

A:

Q: 1200 lb P 1200 lb + 4 ft → VD EV 4 ft G 30

A: ∑Fy=0RA+RB=1200+2500+1200=4900 lbAs the structure is symmetrical thus the support reactions will be…

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A: The FBD of the section is shown below:

Q: ur solution including units and the free body diagrams. 20 KN 3 m A 10 KN 4 m E 20 KN 4 m D C 10 kN

A: Find the force in each members

Q: FN = 51 MN = 98 SN = 83 Problem 1: Refer to the figures below, use the method of joints to find all…

A: We will use equilibrium and method of joints

Q: 1.20 Determine the smallest allowable cross-sectional areas of members CE, BE, and EF for the truss…

A:

Q: USING THE METHODS OF JOINTS. DETERMINE THE FORCE IN EACH MEMBER OF THE TRUSS SHOWN IN THE FIGURE.

A:

Q: Determine the gross area of steel needed to design the bar force members at BC, BE, and AE.

A: ## DETERMINATION OF GROSS AREA OF STEEL NEEDED TO DEGISN THE BAR FORCE MEMBERS ###

Q: Determine the force in all members of the truss shown in the figure below. State whether the members…

A: To Determine :-  Force in all members of the truss and Specify whether they are under compression…

Q: P2 P2 P2 P1 P1 6 ft B 6 ft H E G

A:

Q: : Consider the truss shown in the figure below, and answer the following questions. Figure is not to…

A: