1. The travel time functions (seconds) for link 1 is t₁ = 2 + 2x₁, for link 2 is t₂ = 4 + 4x₂, and for link 3 is t3 = 3 + x3. The total travel demand for this network is 400 trips from node 1 to node 3. Assuming User Equilibrium, determine the total system travel time in vehicle-hour from node 1 to node 3 and the number of trips per route.

1. The travel time functions (seconds) for link 1 is t₁ = 2 + 2x₁, for link 2 is t₂ = 4 + 4x₂, and for link 3 is t3 = 3 + x3. The total travel demand for this network is 400 trips from node 1 to node 3. Assuming User Equilibrium, determine the total system travel time in vehicle-hour from node 1 to node 3 and the number of trips per route.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.22P

See similar textbooks

Similar questions

Q4/ (A) What is the voltage measurement Vx-y , for the circuit shown below. 4v 4v 20 50 y
Please help me with my homework. Thanks! The course subject is Fundamentals of Electronic Communications. 4. A 400 W carrier is amplitude modulated to a depth of 100%. Calculate the total power in case of SSB technique. How much power saving (in W) is achieved for SSB compared to standard
Q2. A symmetrical n-network has a resistance of 7502 in the series arm and 2502 at each shunt arm. a) Calculate the open and short circuit impedances. b) Calculate the characteristic impedance. c) Calculate the propagation constant. d) Find its equivalent T-network.
Two cities A and B are connected by a 200km long train line. A train leaves A for B at 20 km / h at the same time as another train leaves B for A at 5 km / h. In the samemoment a fly leaves from A to B following the train line. The fly flies at 40 km / h until it collides with train B. At that moment it returns instantly and follows the train line until it collides with train A. At that moment it returns instantly and follows the line of the train. train until it collides with train B. The fly continues this process, traveling ever smaller distances until the two trains meet. (It is an ideal problem and the fly does not get squashed by the trains).What is the total distance traveled by the fly?
Discrimination (Selectivity or coordination) Problem: Given the below single line diagram where, the red curve is for a PD1 circuit breaker (Upstream). The blue curve is for a PD2 circuit breaker (Down stream) SUPPLY See the following curves to check the discrimination at the red, green and blue arrows (if the fault happened at the downstream PD2) N NOT DISCRIMINATING WITH UPSTREAM DEVICE 4h 2h 1h 30 m 10 m 50 s 8s 5s 25 0,800 s 0.500 s 0.300 s 200s 0.080 s 0.050s 8838: 0.010s 0.0050 s 0.0010s Current (A) The time selectivity between PD1 and PD2 if the fault happens at PD2 for a current rating coincides with green arrow is Select one: O a At = 47seconds 1/20/22, 4:08 PM O b. At = 27seconds Oc. At = 57seconds Od. At = 37seconds O e. None of these Of At = 7seconds Tripping Time
Question 777 Full explain this question
For a system consist from 3 buses and bus 1 is the slack bus. The data of the system are:- 0.25 Ybusj -0.2 -0.2 0.225 -0.05 -0.025 -0.05 -0.025 p.u. 0.075 V₁=1+j0 p.u., P₂+jQ=0.6+j0.25 p.u., P3+jQ3-0.8+j0.5 p.u. -0.762-j0.826 -0.762+10.826 O 0.762+j0.826 0.762-j0.826 By using Gauss-Siedal method, the voltage of the bus 2 after two iteration is
Bus bar system which ensures continuity of supply during maintanence is ... ... O single bus bar O duplicate bus bar O single bus bar with sectionalization O single bus bar without sectionalization
Translator Translator Using the nodal voltage method, determine the values of I1,I2,V1 and V2 of the circuit shown in the figure.
For calculating the Thevenin's Equivalent Resistance(RIh) at load terminals, remove the load resistance and if a voltage soure by a short circuit and a current source is replaced by an open circuit source is present replaced by an open circuit A_ True B_False
1- Some HV - TL use Double Circuit .instead of One, why To transmit maximum voltage stability, and enhance the steady state stability. 6 To increase the capacity of HVTL and to enhance power system stability. a- All these answers are wrong. d- To increase the impedance of HVTL and to enhance power system stability. 2- Sometimes we use Red Balls with HV.TL in specific locations ? why and where a- To prevent HV.TL from lightning, it located at earth wire over roads and rivers. To give an alarm for the planes, it located at earth wire over roads and rivers. To reduce static transient voltage, it located at earth wire over roads and rivers. d- To reduce static transient voltage, it located at earth wire everywhere. 3- How you can read this impulse voltage : 1.2/50 us and at which ? Standard Durations wave front : 1.2 tr, Wave tail duration is defined as 50 m.si as in International Standard). C Durations wave front : 1.2 tr ( where tr is the transient time ), Wave tail duration is defined…
Q1 A three bus system has the following bus power and voltage specifications: Bus Real Reactive Generated Generated Voltage Bus type Power Power Real Reactive (p.u.) Demand Demand Power Power (p.u.) (p.u.) (p.u.) (р.и.) 0.4 0.25 unspecified unspecified 1.05 + j0.0 Slack 1.5 0.9 unspecified P-Q 3 1 unspecified 1.02 Р-V (magnitude) Angle unspecified The Ybus matrix is shown as follows: [542-68° 22Z116° Y = 22/116° 312108° 582-63° 33Z107° p.u. bus 312108° 33/107° 672-67° (a)Determine the voltages at bus 2 and bus 3 after first iterations using Gauss Seidel. Use flat start voltage. (b) If the final value of voltage at buses 2 and 3 are 12-5.13° p.u. and 1.02Z-8.32° p.u. respectively, calculate the following; (i) Real and reactive power generated at bus 1 (ii) Power losses in branch (2-3) 1. 2.