Kindly solve all including Q3 too in the order to get positive feedback please show me neat and clean work for it 1. (-) The switch in the circuit below has been in position a for a long time before it moves to position bat t = 0. Obtain a differential equation (in terms of capacitor voltage ve and circuit parameters, R, L, C)that describes the behavior of the circuit for t > 02.3гол atuv150VNc+ESAME32-2mRL2mH32nre) External circuitry (not depicted) causes the initial inductor current to be i(0) = 2A. Determinethe values of all initial conditions needed to obtain an equation for the inductor current i(t), t≥ 0.....) Obtain an equation for the inductor current i(t), t≥ 0. Estimate the duration of the transientresponse. If the response exhibits oscillatory behavior, determine the oscillation frequency.

Answered: Image /qna-images/answer/b828af18-6ab1-4ca7-ba63-c1b9cc4a6b49.jpg

1. (-) The switch in the circuit below has been in position a for a long time before it moves to position b at t = 0. Obtain a differential equation (in terms of capacitor voltage ve and circuit parameters, R, L, C) that describes the behavior of the circuit for t > 0 2. 3 гол ан uv 150V Nc + ESAE 32-2 m R L 2mH 32n re) External circuitry (not depicted) causes the initial inductor current to be i(0) = 24. Determine the values of all initial conditions needed to obtain an equation for the inductor current i(t), t ≥ 0. .....) Obtain an equation for the inductor current i(t), t≥ 0. Estimate the duration of the transient response. If the response exhibits oscillatory behavior, determine the oscillation frequency.

1. (-) The switch in the circuit below has been in position a for a long time before it moves to position b at t = 0. Obtain a differential equation (in terms of capacitor voltage ve and circuit parameters, R, L, C) that describes the behavior of the circuit for t > 0 2. 3 гол ан uv 150V Nc + ESAE 32-2 m R L 2mH 32n re) External circuitry (not depicted) causes the initial inductor current to be i(0) = 24. Determine the values of all initial conditions needed to obtain an equation for the inductor current i(t), t ≥ 0. .....) Obtain an equation for the inductor current i(t), t≥ 0. Estimate the duration of the transient response. If the response exhibits oscillatory behavior, determine the oscillation frequency.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 94CP: Consider the circuit below, (a) What is the initial current through resistor R2? when the switch is...

See similar textbooks

Similar questions

The current in the RL circuit shown here increases to 40% of its steady-state value in 2.0 s. What is the time constant of the circuit?
A 2.0-F capacitor is charged to a potential difference of 12.0 V and then connected across a 0.40-mH inductor. What is the current in the circuit when the potential difference across the capacitor is 6.0 V?
The current in the RL circuit shown below reaches half maximum value in l.75 ms after the switch S1is town. Determine (a) the tine constant of circuit and (b) the resistance of the circuit if L = 250 mH.
Apply the loop rule to loops abgefa and cbgedc in Figure 21.47.
When a wire is connected between the two ends of a solenoid, the resulting circuit can oscillate like an RLC circuit. Describe what causes the capacitance in this circuit.
A radio receiver uses an RLC circuit to pick out particular frequencies to listen to in your house or car without hearing other unwanted frequencies. How would someone design such a circuit?
Presbycusis is a hearing loss due to age that progressively affects higher frequencies. A hearing aid amplifier is designed to amplify all frequencies equally. To adjust its output for presbycusis, would you put a capacitor in series or parallel with the hearing aid's speaker? Explain.
Do Kirchhoff’s rules apply to circuits that contain inductors and Capacitors?
Why is the power dissipated by a closed switch, such as in Figure 21.43, small?
Apply the loop rule to Loop afedcba in die preceding problem.
Consider the circuit below, (a) What is the initial current through resistor R2? when the switch is closed? (b) What is die current through resistor R2 when the capacitor is fully charged, long after die switch is closed? (c) What happens if the switch is opened after it has been closed for some rime? (d) If the switch has been closed for a time period long enough for the capacitor to become fully charged, and then the switch is opened, how long before the current through resistor R1 reaches half of its initial value?
An electronic apparatus may have large capacitors at high voltage in the power supply section, presenting a shock hazard even when the apparatus is switched off. A “bleeder resistor" is therefore placed across such a capacitor, as shown schematically in Figure 21.50, to bleed the charge from it after the apparatus is off. Why must the bleeder resistance be much greater than the effective resistance of the rest of the circuit? How does this affect the time constant for discharging the capacitor?