1. The following circuit shows a discrete common source MOSFET ampliierThe MOSFTE is n-channel MOSFET.The transconductance of the n-channel MOSFET (g) is 3 mA/V.Rig 100 kN, RGI =47 MQ, Rir 100 kQ, Rm= 10 MO R=2 kQ, Rp -4.7 k£2,RL 10 k2, Rsig 100 k2, Cgs 1 pF, Cgd0.2 pF VAThe C-S MOSFET amplifier has three low break frequencies in low frequency band atfLI=1 Hz (caused by Cei), fiz2 100 Hz (caused by Cs), fo= 10HZ (caused by Cc)(a) Draw small signal equivalent circuit of the amplifier in low frequeney band.VDDRG1RDCc2Q1Cc1RLRsigRG2VsigRS

Answered: Image /qna-images/answer/d8691519-990d-4046-87dd-4a9312a8f37d.jpg

1. The following circuit shows a discrete common source MOSFET amplilier The MOSFTE is n-channel MOSFET. The transconductance of the n-channel MOSFET (g) is 3 mA/V. Raig 100 k2, RGI 47 MS, Raig 100 kC, Ra2 10 MQ, Rs=2 kQ, Rp-4 7 k2, RL 10 k2, Rsig 100 k2, C 1 pF, Cgd0.2 pF VA n The C-S MOSFET amplifier has three low break frequencies in low frequency band at fLI=1 Hz (caused by Cei), fiz 100 Hz (caused by Cs), fo= 10HZ (caused by Ccz) (a) Draw small signal equivalent circuit of the amplifier in low frequency band. VDD RG1 RD Cc2 Q1 Cc1 RL Rsig RG2 Cs Vsig RS

1. The following circuit shows a discrete common source MOSFET amplilier The MOSFTE is n-channel MOSFET. The transconductance of the n-channel MOSFET (g) is 3 mA/V. Raig 100 k2, RGI 47 MS, Raig 100 kC, Ra2 10 MQ, Rs=2 kQ, Rp-4 7 k2, RL 10 k2, Rsig 100 k2, C 1 pF, Cgd0.2 pF VA n The C-S MOSFET amplifier has three low break frequencies in low frequency band at fLI=1 Hz (caused by Cei), fiz 100 Hz (caused by Cs), fo= 10HZ (caused by Ccz) (a) Draw small signal equivalent circuit of the amplifier in low frequency band. VDD RG1 RD Cc2 Q1 Cc1 RL Rsig RG2 Cs Vsig RS

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Needs Complete solution with 100 % accuracy.
Which of the following statement is true? Conjugate matching guarantees the maximum output power regardless of input power. The optimum source impedance for the minimum noise figure can be obtained by conjugate matching condition. O The first stage is the most important to minimize the overall noise figure in cascaded blocks An oscillator cannot be built with a single stage amplifier. None of the above
help me please..................
Please show each step with the formulas used
Given the four statements, which of the following statements are true about an op-amp integrator? i. For an op-amp integrator wilh R = 10OKOhms, C = 10UF and a sine wave inpul waveform, the output waveform is a cosine waveform. %3D ii. For an op-amp integrator with R = 100KOhms, C = 10uF and a triangular input waveform, the output waveform is a square wave. iii. For an op-amp integrator with R- 100KOhms, C =10uF and a sine wave input waveform, the output waveform is a sawtooth waveform. v. For an op-amp integrator with R10OKOhms. C lCuF and a square wave input waveform, the output waveform is a triangular waveferm.
An inverting op amp circuit has RF = 3 kilohms and RIN = 1 kilohm. What is the gain of this circuit?
For a Fixed bias circuit having Rc-2.2K0, RB-2400, Vcc=12v and current amplification factor is 100 and the current flowing through the base is 20µA, the value if Collector current in saturation is 3mA O OA O 5.4mA O 1mA
VCC R2 RC- RI RL R1 RE VEE Assume: B=100, VA=150, Vcc=12V, VEE=GND, Rr=2K, R1=160K, R2=300K, RE=3K, Rc=2.2K, and R1=100K. Convert the circuit to a common-collector circuit. Draw the new circuit (assume the same values for the input and load resistances). Then compute the terminal voltage gain, and Rin (for the whole circuit), re-computing any parameters that you need to solve.
A type II compensator implementation for the above Buck converter is shown below. Ce2 Vout Cet HH Ret Vctrl R2 E/A Vset What should be the voltage Vref in the above type II compensator to produce 5V DC output if R# = 4k and R2=1k. а. Vet b. Write the small signal gain equation (-ctrl) between Vetrl and Vout- out с. Does R2 present in the above gain equation. Please add some explanation. d. How many poles and how many zeros are produced by this type II compensator?
(d) An instrumentation amplifier is used when the application signal is very low. For the circuit shown in Figure Q2(d), calculate the applied input vin of the circuit to get the output of 5V at vo. Let Rr=360k 2 and R₁ = 12k 52. Rf www R1 Vec www Vo -Vec Figure Q2(d) (e) Illustrates instrumentation system for temperature measurement with the help of block diagram. Vin uA741
For the circult shown in the given figure. Rc-2.4 k0, Rg-10 ko. Pmin-50, and Vcc=5 V. Determine the range of values of Vgg 50 Ic that the transistor is in saturation. Assume Vy-0.6 V and VCEsat -0.2 V. The range of values of VB8 Is VBB> 12 V Ra VAR со Va VCE OE RC Ncc
Q3) For the regulator circuit shown in figure below, Vin-15 V, Rs-10 2, Vz-9.1 V, VBE=0.8V, and R=40 2. What are the values of output voltage, input current, the load current, and collector current. 102016 2-8594 Vin R$ Ⓡ R₂ Vout