Answered: 1. The cylindrical tank has an outer…

1. The cylindrical tank has an outer radius of 2 m and a wall thickness of 35 mm. If the tank is pressurized to 1.75 MPa, determine the circumferential stress.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question A steel rod 15 m long is at a temperature of 15°C. The values of a = 12 x 10-6m and E = 200…

Q: A straight wire 15 m long is subjected to tensile stress of 2000 kgf/cm². Elastic modulus is 1.5x106…

A: We have to calculate the temperature change to produce the same elongation

Q: A thick cylindrical pressure vessel of inner diameter D, and outer diameter D is subjected to an…

A: The hoop stress and the radial pressure variation can be obtained using Lame's equation:

Q: Figure Q4(a) shows the stress-strain curves of material A and material B. A circular rod of material…

A: It is required to determine the yield stress. From the figure, the yield stress for material A is…

Q: Question: The original diameter of wire AB shown in Fig. 1 is 5mm and it has the average…

A: The elongation of the bar is directly proportional to the tensile force and the length of the bar…

Q: Problem 1. In a test on an aerosol can it was loaded to a gage pressure p = 69.0 psi. While…

A: inside pressure p=69 psinormal load N=400 lb and torque T=250 lb-indiameter d=3.0 in and radiud…

Q: The material of a rubber balloon has a Poisson's ratio of 0.5. If uniform pressure is applied to…

A: Given Data; Poisson's Ratio = (μ) = 0.5 Uniform pressure applied to blow to balloon. To Determine…

Q: A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank…

Q: A thick cylindrical pressure vessel of inner diameter D, and outer diameter D is subjected to an…

A: Given- Inner dia DiOuter dia DoInternal fluid pressure =pcircumferential tensile stress=py

Q: A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank…

A: Given data, The outside diameter of the tank, d = 180mm Wall thickness t, = 13mm Pressure in the…

Q: A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank…

Q: A body is subjected to stresses as shown in the figure given below. 90 MPa 35 MPa 145 MPa The FOS as…

Q: What is the working strength of a 2" bolt which is screwed up tightly in a packed joint when the…

A: As per guidelines we need to answer only first question so please repost rest questions separately

Q: Two strain gages are mounted on a thin-walled cylindrical pressure vessel. One strain gage is…

A: It required to find Longitudinal stress Hoop stress Gage pressure

Q: 1) The plastic polymer cylindrical pipe is carrying flowing water at 0.5 N/mm pressure. The pipe has…

Q: Theory of Failure Question 1: The uniaxial yield stress of a material is 866 MPa. According to von…

A: Yield stress- σy=866 MPa, It is needed to find the shear yield stress as per the Von-mises…

Q: 2.41 The device shown consists of a disk that is rotated by a shaft. The disk is positioned very…

Q: If Surface tension for a Jet form is 0.05 N/mm and diameter of Jet is 0.3 Cm then pressure will be?

A: given- surface tensionσ=0.05 N/mmdiameter of jetd=0.3 cm=3 mm

Q: A 0.35-m long steel rod with a round cross-section (25 mm) is resting on a frictionless surface. The…

A: The given data is: Length of steel rod (L) = 0.35 m Diameter of steel rod (d) = 25 mm Coefficient of…

Q: A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank…

A: The given figure is shown below:

Q: A rigid steel bar is supported by three rods as shown. There is no strain in the rods before the…

Q: The thin-walled tube is used as a beam to support the uniformly distributed load of intensity wo as…

A: For the given beam and cross-section, the maximum load w0 for allowable bending stress of 1000…

Q: A thin cylinder of internal diameter 1 m and thickness 0.02 m contains a gas. The tensile stress in…

A: A thin cylinder- Internal diameter d = 1 m, Thickness t = 0.02 m, Tensile stress σ=100 MPa. To Find-…

Q: bar of varying square cross-sect mmetrically as shown in the figure. Loads shown e placed on one of…

Q: A cylindrical tank holding oxygen at 2.091 kPa pressure has an outside diameter of 409 mm and a wall…

Q: The material of a rubber balloon has a Poisson's ratio of 0.5. If uniform pressure is applied to…

A: Given- Poisson's ratio- μ=0.5, Volumetric strain = ?

Q: A 25m steel rod with diameter of 20 mm is secured between rigid supports at both ends. If there is…

A: Stress due to temperature difference can be calculated with the help of the following equation, σ =…

Q: 1. At the proportional limit, a certain material has a stress of 78 MPa as the strain is 0.0004.…

A: Given data , Material stress=78MPa Strain = .0004 Calculate modulus of elasticity of…

Q: True stress-strain behaviour of a metal is given by the flow curve equation o = 1750 €0.37 where o…

Q: Examples Example 3.1. The 50-lb lamp is supported by the two-rods shown. Determine the angle of…

Q: A cylindrical shell of 100 cm diameter made of mild steel plate is to be subjected to an internal…

A: given-1 diameter d=100 cminternal pressure p=10 kg/cm2stress σy=200 kg/cm2FOS=4

Q: get. The shear stress at a point in a liquid is found to be 0.03 N/m². The velocity gradient at the…

A: Given data : Shear stress (ζ)=0.03 N/m2Velocity gradient dudY=0.15 s-1

Q: 1. As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is…

A: Given Data Initial temperature (T1) = 10° C Final temperature (T2) = 95° C EAl = 70 GPa = 70 ×…

Concept explainers

Pressure and Stress

Question

100%

mechanics of deformable bodies

1. The cylindrical tank has an outer radius of 2 m and a wall thickness of 35 mm. If the tank is pressurized to 1.75 MPa, determine the circumferential stress.

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

5
A circular metallic rod of length 250 mm is placed between two rigid immovable walls as shown in the figure. The rod is perfect contact with the wall on the left side and there is a gap of 0.2 mm between the rod and the wall on the right side. If the temperature of the rod is increased by 200°C, MPa. the axial stress developed in the rod is_ Young's modulus of the material of the rod is 200 GPa and the coefficient of thermal expansion is 10-5 per°C. 250 mm 0.2 mm
I need the answer quickly
A cube contracts in volume by 0.05% when acted upon by normal uniform pressure of 2x 106 N/m? on all sides. The bulk modulus of its material is (а) 400 MPа (4000 MPa (d) 40000 MPa (b) 40 MPа
Q2)A filament 0.5m long and having a cross-sectional area of 1mm2 was stretched to breaking. If the breaking stress for the filament was found to be 109 Pa, calculate the mass which was hung on the filament to break it. Assuming the filament stretched linearly up to breaking, calculate the amount by which the filament stretched. (Young’s modulus for the material = 6 x 1010 Pa) If the assumption in (b) was justified, what might the material have been? State in one word.
A solid cube of side 1 m is kept at a room temperature of 32°C. The coefficient of linear therma expansion of the cube material is 1 x 105/°C and the bulk modulus is 200 GPa. If the cube is constrained all around and heated uniformly to 42°C, then the magnitude of volumetric (mean) stress (in MPa) induced due to heating is و او را
Question 42 A circular beam of 300 mm diameter is made up of a material having permissible stress 80 N/mm². The moment of resistance of the beam is
Do it
A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank is 150mm and the wall thickness is 9mm. If the air in the tank is pressurized to 15.2MPA, determine: (a) the longitudinal and hoop stresses in the wall of the tank. (b) the maximum shear stress in the plane of the cylinder wall. (c) the absolute maximum shear stress on the outer surface of the cylindrical wall. Answers: (a) Ojong = i MPa Onoop = MPa (b) Tmax i MPa (c) Tabs max = MPa i
Solid mechanics
1.31 A steel rod, which is free to move, has a length of 200 mm and diameter of 20 mm at a temperature of 15°C. If the rod is heated uniformly to 115°C, determine the length and the diameter of this rod to the nearest micron at the new temperature if the linear coefficient of thermal expansion of steel is 12.5 x 10° m/m/°C. Is there a stress on the rod at 115°C?