1. The coefficients of static and kinetic friction between the 100 - kg block and the inclined plane are 0.30 and 0.20, respectively. Determine (a) the friction force F acting on the block when P is applied with a magnitude of 200 N to the block at rest (b) the force P required to initiate motion up the incline from rest, and (c) the friction force F acting on the block if P = 600 N

1. The coefficients of static and kinetic friction between the 100 - kg block and the inclined plane are 0.30 and 0.20, respectively. Determine (a) the friction force F acting on the block when P is applied with a magnitude of 200 N to the block at rest (b) the force P required to initiate motion up the incline from rest, and (c) the friction force F acting on the block if P = 600 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A B A C D Blocks A, B, and C have weights of 93 N, 25 N, and 15 N, respectively. The coefficient of static friction between A and B is 0.3, between B and C, 0.4, and between block C and the ground, 0.35 Determine the smallest force P that will causes impending motion. Determine the friction force between A and B Determine the friction force between B and C
PROBLEM 5 The uniform block, 4'x 3'as shown weighs 2001b. It is pulled up the incline by the force F= 250 lb. Determine the maximum and minimum values of d so that the block does not tip over as it slides up the incline. The coefficient of friction is 0.21. +3 IL
The cross section of a wood beam carries a bending moment M of magnitude 20R lb.-in. acting at 100 to the horizontal. Determine(a)the angle between the neutral axis and the horizontal; and (b) the maximum bending stress acting on the cross section. Note: ( R=990)
The homogeneous disk of mass m is resting on the right-angled supporting surfaces shown. The tension P in the cord is very gradually increased from zero. If the friction at both A and B is characterized by us = 0.23, what happens first - does the homogeneous disk slip in place or does it begin to roll up the incline? Determine the value of P at which this first movement occurs. Assume 0 = 25° B 0.75r/ Answer: P = i P Ө mg
A 10-lb force is pushing the 40-lb block as shown. The incline angle of the plane is α=40º . The coefficient of static friction between the block and the incline is μs = 0.75 and the coefficient of kinetic friction is μk = 0.65. Will the block slide on the plane? If it does, will it slide up or down the plane? What is the friction force between the block and the plane?
Show solution in solving the problem
The cross section of a quarter circular concrete block JKL as shown in Figure 5 is located at thebottom of a reservoir. The width (perpendicular to the paper) is 3 m. The specific weight of theconcrete block is 24 kN/m3. The coefficient of friction between the base of the block and thefoundation is 0.43. Determine if the concrete block is stable or not against sliding and overturningif the water is:A. At side XB. At side Y, with the same water level as A.
k=2 lb/ft -¨¨¨¨¨ B Two blocks A and B have a weight of 11 lb and 6 lb, respectively. They are resting on the incline for which the coefficients of static friction are μA = 0.16 and μB = 0.23. Determine the angle 0 which will cause motion of one of the blocks. What is the friction force under each of the blocks when this occurs? The spring has a stiffness of k = 2 lb/ft and is originally unstretched. Determine the smallest angle which will cause motion of one of the blocks. Determine is the friction force under the block A at this angle. Determine is the friction force under the block Bat this angle.
The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for all contacting surfaces is µ = 0.268. Determine the following: a. What value of P in kN would be required to push to the right the wedge under the block? b. What value of P in kN would be required to pull to the left the wedge under the block? Assume the block A is stll in contact with the wall just as motion starts.
Dont forget to draw the FREE BODY DIAGRAMS ALSO PLEASE! (:
Friction-static and rigid bodies DRAW YOUR OWN FIGURE.