1. Suppose you are flying a 7,784 kilograms aircraft at 14,630 meters where the air density is 0.2062 kilograms/cubic meter. Your current cruising speed is 290 kilometers/hour (108 m/s) and the wing area of the aircraft is 186 square meters. You need to make some altitude changes and will need to know the "Lift Coefficient" of the aircraft in order to do so. What is theCl for your aircraft?

1. Suppose you are flying a 7,784 kilograms aircraft at 14,630 meters where the air density is 0.2062 kilograms/cubic meter. Your current cruising speed is 290 kilometers/hour (108 m/s) and the wing area of the aircraft is 186 square meters. You need to make some altitude changes and will need to know the "Lift Coefficient" of the aircraft in order to do so. What is theCl for your aircraft?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A: An aircraft flying steady and level at true airspeed of 720 km/hr at sea level. The aircraft have two engine at 85.4kN thrust each and drag polar equation is CD-0.035+0.05 CL2, wing area is S-187m². What is aircraft weight? Cal. na?
You are designing an airfoil for a new hobby RC plane. Because of your limited knowledge, you have mistakenly approximated your airfoil as an ellipse with a = 75mm and b = 12mm. Here, “a” is the depth of your wing and “b” is the thickness. Your plane travels through the air at approximately 20mph (8.9m/s). As it does so, skin friction produces a drag-induced heat of 800W on your wind, of length 1m. Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), TInfinity = 25oC a) What is the average temperature of your wing? Assume an ellipse perimeter of approximately 200mm.
An air whose cross-sections are visible in the figure on the side Channel 40 cm diameter and 60 cm tall test section references The air temperature is 200oC. At the entrance of the Test section A uniform airspeed of 2 m/s was measured.a) the number of Reynolds at the end of the test section (Rex)calculate.b) limit layer thickness at the end of the test sectioncalculate.c) air velocity test on centerlinewhat percentage increases by the end of the section,calculate.d) local surface friction at the end of the test sectioncalculate the coefficient. v = 1,516 . 10-5 m2/s.
Wind provides an increasingly important source of renewable energy in certain locations of the world. In fact, wind was the second largest renewable energy source worldwide (after hydropower!) and provided more than six percent of global electricity in 2020; in the U.S. that number was 8.4%. Suppose that wind turbines can convert up to 30% of the kinetic energy of incoming wind blowing through their blades into electricity (i.e., useful shaft work). In the following, we will analyze the power output of a wind turbine with a diameter of d 80 m placed at an offshore location where the wind blows steadily at an average speed of 20 knots. Explicitly state all relevant approximations or assumptions. = (a) Draw a diagram that includes appropriate elements for assessing the amount of work extracted from the wind turbine. Your diagram should have annotated any known or approximated proper- ties. What is your system and surroundings? What kind of boundary divides these two? Hint: In terms of…
A flat-bottomed raft is traveling across a shallow lake at 6 ms-¹. The lake is 10 cm deep. If the raft has a surface area of 3 m² and the lake is full of water with viscosity of 0.001 Pa s, determine the force required to maintain the raft's speed. [0.18 N]
2/A- Airbus 320 fly in steady level flight with altitude 10.5 km and the density at this level p=0.3877 kg/m³, mass of aircraft 6500 kg, wing area 124 m², CD = 0.015+ 0.02 CL², maximum thrust at sea level 53.015 kN. Calculate maximum velocity. C00
An aircraft has a wing area of 70 m? and a wing loading of 2500 N/m2. The air density could be taken as 0.45 kg/m3. The drag equation for the aircraft is given as: Cp-0.016+0.055 C2 Calculate its minimum drag speed in m/s. Keep 2 decimals.
Q5/A 400 m² light-colored swimming pool is located in a normal suburban site, where the measured wind speed at 10 m height is 2 m/s. The water temperature is 25 °C, the ambient air temperature is 10 °C, and relative humidity is 60%. There are no swimmers in the pool, the temperature of the make-up water is 20 °C, and the solar irradiation on a horizontal surface for the day is 15 MJ/m2-d. Neglect heat losses due to evaporation and radiation. How much energy must the solar system supply (Qss) to the pool to keep its temperature to 25 °C? Take: a = Solar absorptance (a = 0.85 for light-colored pools; a = 0.90 for dark colored pools).
A flat plat 1200 cm x 280 cm is kept in a fluid which has a velocity of 570 m/s.lIf resultant force acing on the plate is 280 kN then calculate 3 the lift force. Assume the density of the fluid is 2.3 kg/m³ and the viscosity of the fluid is 0.21Poise. pkg/m³ vm/s Lift Drag
Please correct answer
You are designing an airfoil for a new hobby RC plane. Because of your limited knowledge, you have mistakenly approximated your airfoil as an ellipse with a = 75mm and b = 12mm. Here, “a” is the depth of your wing and “b” is the thickness. Your plane travels through the air at approximately 20mph (8.9m/s). As it does so, skin friction produces a drag-induced heat of 800W on your wind, of length 1m. Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), TInfinity = 25oC a) What is the Reynold’s number? Hint: “D” is taken to be the thickness for an elliptical crosssection. b) What is the Nusselt number? c) What is the convection coefficient? d) What is the average temperature of your wing? Assume an ellipse perimeter of approximately 200mm.
The Antonov An-225 is the heaviest aircraft ever built, with a maximum takeoff weight of 640 metric tonnes. It also has the largest wingspan of any aircraft in operational service. Sea level standard day (sls) conditions for calculations are 15°C; 101.3kPa Rotate speed (Vr) at takeoff (sls): Vr = 154 kts = 1.2×Vmin (1 kt = 0.514 m/s) Cruise Engine Thrust : a) Calculate the lift coefficient for a standard day takeoff b) Calculate the drag coefficient at cruis Fcruise = 0.85 Fmax Engine maximum thrust: Factual,max = Fsls,max×δ θ½ δ = Pactual/Pref; and θ = Tref/Tactual