1. Suppose a person is 182 cm tall. A typical blood pressure is often given as110/70 mm Hg, with a mean pressure of 80 mm Hg.A.Do you think this is the gauge pressure or absolute pressure? Why?6,If the pressure at the top of the head is about 39 mm Hg, how far away isthis person's head from the heart? Assume the density of blood is about 6%higher than that of water.C, What then would be the blood pressure of this person at their feet?D. Suppose this person suffers a puncture wound around the same height asthe heart where the opening is about 3 mm in diameter. How far could bloodshoot from their body assuming it comes out horizontally with 0 m/s initialhorizontal velocity?Please show me how to soluethes problem iN nEat andclené de fail. Show alaequatiins that I must aSEfo GetneatI mUstcorrect asweres.4o Ger heThank gon !!

Since you have posted a question with multiple sub-parts, we will solve first three sub- parts for…

1. Suppose a person is 182 cm tall. A typical blood pressure is often given as 110/70 mm Hg, with a mean pressure of 80 mm Hg. A. Do you think this is the gauge pressure or absolute pressure? Why? 6, If the pressure at the top of the head is about 39 mm Hg, how far away is this person's head from the heart? Assume the density of blood is about 6% higher than that of water. What then would be the blood pressure of this person at their feet?

1. Suppose a person is 182 cm tall. A typical blood pressure is often given as 110/70 mm Hg, with a mean pressure of 80 mm Hg. A. Do you think this is the gauge pressure or absolute pressure? Why? 6, If the pressure at the top of the head is about 39 mm Hg, how far away is this person's head from the heart? Assume the density of blood is about 6% higher than that of water. What then would be the blood pressure of this person at their feet?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A differential manometer is connected to two pipes as shown in Fig. 2.31. The pipe A is containing water and the pipe B is containing an oil of specific gravity 0.8. Find the difference of mercury levels, the pressure difference in the two pipes be 80 kPa. [Ans. 426 mm] Water- 3.5 m B To Fig. 2.31. Fluid Pressure and its Measurement 37 300 Fig. 2.32. -Oil of sp. gr. 0.8 Copyrighted materia B
1. The density of an oil is 850 kg/m3. Find its relative density (or specific gravity) and Kinematic viscosity if the dynamic viscosity is 5 x 10-3 kg/ms. 2. If the viscosity of water at 70 °C is 0.00402 poise and its specific gravity is 0.978 determine its absolute viscosity in Pa-s and its kinematic viscosity in m²/s and in stokes 3. Calculate the Reynolds number, Re for water flow in a circular pipe. The diameter of the pipe is 50 mm, the density of water is 998 kg/m³, the volumetric oil flowrate is 720 L/min, and the dynamic viscosity of water is 1.2 centipoise
Fig shows a U-tube differential manometer connecting two pressure pipes at A and B. Pipe A contains a liquid of specific gravity 1.8 under the pressure of 101 kN/m². The pipe B contains oil of specific gravity 0.7 under the pressure of 207 kN/m2. Find the difference of pressure measured by mercury as fluid filling U-tube in mm. The value of x and y are 2 m and 1.1 m respectively. Pe S, \Mercury The Mercury level difference (h ) in mm
The sketch shows an oil manometer that is connected between two pipes which transport water. The density of water can be taken as 998kg/m3, the specific gravity of glycerol is 0.76 and atmospheric pressure is 100 kPa. The respective dimensions (as shown on the sketch) are given below: h1 = 0.17 m h2 = 350 mm h3 =15cm. If the pressure gauge gives a reading of 19 kPa, what is the absolute pressure in pipe B?
The gauge pressure of a pneumatic cylinder reads 40 lb/in.2 when the volume is 30 in.3. The cylinder is compressed until the gauge reads 60 Ib/in.?. What is the volume in the cylinder after the gas is compressed? (round to the nearest whole number # #)
In Figure below all fluids are at 20 deg.C. Determine pressure at point B, if pressure at point A is 150 kPa and weight of air is neglected. Use the table below for the densities at 20 deg.C. Liquid p. kg/m Kerosene - Ammonia 608 Benzene 881 Air Carbon tetrachloride 1590 Benzene Ethanol 789 Ethylene glycol Freon 12 B 1117 40 cm 9 cm 1327 20 cm Gasoline 680 14 cm Glycerin Kerosene 1260 t8 cm 804 Mercury- Water Mercury Methanol 13,550 791 SAE 10W oil 870 SAE 10W30 oil 876 SAE 30W oil 891 SAE 50W oil 902 Water 998 Seawater (30%e) 1025
Q5: The compart ments (B) 4 CC) in figure below are closed & filled with air. When the gauges (A) (D) read as indicated, when should be the value of Cx) for gaugeCE)? (Mercury in each U-tube gauge) 2.07 bar C B. 254 Air Air E.
The figure shows a sensor indicating a gauge pressure reading of 1.5 kPa. The fluids are at 20°C Determine: a) the height hb. b) the height hc.The specific weight of air is 12.0 N/m3.
2. A closed vessel contains air at a pressure of 160 kN/m2 gauge and temperature of 30oC. The air is heated at constant volume of 60oC with the atmospheric pressure as 759 mm Hg. What is the final gauge pressure? (3 DECIMALS IN FINAL ANSWER PLS)
1. A differential manometer is used to measure the drop in pressure between two points in a process line containing water. The specific gravity of the manometer fluid is 1.05. The measured levels in each arm are shown below. Calculate the pressure drop between points 1 and 2 in dynes/cm?. 3.4 Pressure 63 p = 1.00 g/cm? 382 mm 374 mm P = 1.05 g/cm"
2. The reading on the pressure gauge fitted on a vessel is 34bar. The atmospheric pressure is 1.03 bar and the value of g is 9.81m/s?. Find the absolute pressure in the vessel.
1. Two pipes A & B caries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe A is 75 cm above the pipe B. The height of oil in right limb is 35 cm. Also, the mercury level difference is found in right limb as 60 cm. Find the pressure difference between these two pipes in kPa. Also find the pressure equivalent in water head in mm. A. The difference of pressure between two pipes (PA-Pa) (Unit is in kPa) = B. Equivalent to Water head in mm =