1. Refer to Figure 1. Assume all diodes are ideal, v,= V,VZ sin ot where V, = 240 volt, w = 2nf. f=50Hz and t = time in second (s). Given the magnitude of ripple voltage, Vr(p-p) = 6V. a. Describe clearly the function of Block A, Block B and Block C b. Find the peak value of vị, v, and v3 c. Draw and completely label the waveforms of v, v, and v3 d. Calculate the average value of v; e. What is the DC value of v,? 2000 V2 1002 Vz=9V |1000내 10 :1 Block A Block B Block C Figure 1

1. Refer to Figure 1. Assume all diodes are ideal, v,= V,VZ sin ot where V, = 240 volt, w = 2nf. f=50Hz and t = time in second (s). Given the magnitude of ripple voltage, Vr(p-p) = 6V. a. Describe clearly the function of Block A, Block B and Block C b. Find the peak value of vị, v, and v3 c. Draw and completely label the waveforms of v, v, and v3 d. Calculate the average value of v; e. What is the DC value of v,? 2000 V2 1002 Vz=9V |1000내 10 :1 Block A Block B Block C Figure 1

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

Draw vx and v0 according to the input voltages in the circuit shown in the figure. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, the threshold voltages of diodes will be VE = 0.7V.
For the circuit shown in the Figure, if the diodes are silicon diodes with Vp(on)=0.7 V, and VIN=50 sin wt V, V1 =6 V and V2 = 16 V, then the value of VouTP-p) is: R, D VaN Vout v1事 2章 Oa. 25.4 V Ob. 27.4 V Oc. 29.4 V Od. 23.4 V
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
For the circuit shown in figure 1, the diodes is in complete model and the resistance of both diodes are 5 Ohm. Find the current in the resistance RL. When the both switch S1 and switch S2 are ON. v1= 6V, V3 =3 Vv2=12 V.
Find the values of I and V for the circuits of Figure below, assuming that the diodes are ideal.
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
points) For the circuit shown below, sketch to scale the output V, waveform and draw the transfer characteristic (V. versus Vi), Assume the diodes are ideal. V₁ =15-sin wt Zloks www loks # HIF 4V + Vo
In the circuit shown in the figure, draw vx and v0 with a scale according to the input voltages. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, threshold voltages of diodes shall be VE = 0.7V.
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2