1. (Problem 2.36 from the text book) The 5-ft high concrete post is reinforced with six steel bars, each with a 3 -in. diameter. Knowing that the Modulus of Steel, Es = 29 x 10° psi, and the Modulus of Concrete, Ec = 3.6 × 10° psi, determine the maximum centric force that can be applied if the allowable normal stress is 15 ksi in the steel and 1.6 ksi in the concrete. 5 ft 10 in. 10 in.

1. (Problem 2.36 from the text book) The 5-ft high concrete post is reinforced with six steel bars, each with a 3 -in. diameter. Knowing that the Modulus of Steel, Es = 29 x 10° psi, and the Modulus of Concrete, Ec = 3.6 × 10° psi, determine the maximum centric force that can be applied if the allowable normal stress is 15 ksi in the steel and 1.6 ksi in the concrete. 5 ft 10 in. 10 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
Three high-strength concrete poles, with an effective cross- sectional area of 40, 000m * m ^ 2 and a length of 2 m, support a stiff steel plate. The center post is 1 mm shorter than the others before the load P is applied. If the concrete's allowed compressive stress is 20 MPa, calculate the maximum load that can be carried. E = 30GPa for concrete
A rectangular beam has the dimensions (see Figure) b = 12 in, h= 20 in, and d= 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in?. The concrete compressive strength fe is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the stress in the steel caused by a bending moment M = 10 ft-kips. 9 - 6.78 in, I- 4067 in, Es = 29000000, E - 3600000 L17 in. 20 in. 3 #9 bars (A, - 3.00 in.) 3 in. -12 in.- Select one: a. 2525 psi b. 2412 psi C. 2615 psi d. 2817 psi
A rectangular beam with a width of (9536/1150)-in,and effective depth of (9536/900)in is Reinforced with a single high strength steel bar that has a cross- sectional area of 0.42 in2.The bar has a normal tensile strength of 145 ksi, linear stress-strain curve to failure, and a strain at failure of 1.8 percent. The concrete strength fc= 6000 psi. Calculate the nominal flexural strength of the section.
Determine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 340 mm Thickness of flange tf = 140 mm Effective depth d = 350mm Effective concretee covering d' = 75mm Compressive strength of concrete fc' = 34.5 MPa Yield stress of steel bar fy = 375 MPa Mu = 415 kN-m As = _________ mm2
Q-A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm² at centre of gravity of the section. The prestress in the tendons is 1000 N/mm². Assuming modular ratio as 10, find the stress (N/mm2) in concrete.
21. The column of reinforced concrete is loaded with P = 8000 lbs. The modulus of elasticity (E) is 4.2E6 psi and the Poisson ratio is 0.15. 16in 16in What is the normal stress along section b-b? a. -15.625 psi b. -7.81 psi c. -2.60 psi d. -11.04 psi
A rigid steel plate is supported by three posts of high-strength concrete each having an effective cross-sectional area A = 40,000 mm2 and length L = 2 m (see figure). Before the load P is applied, the middle post is shorter than the others by an amount s = 1.0 mm. The allowable compressive stress in the concrete is 20 MPa and E of concrete is 30 GPa. What is the minimum load P (kN) needed to close the gap? P S
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 andE = 200 GPa, Determine the total resulting strain in the x- direction. %3D
The maximum load of 200 KN was applied on a cylindrical specimen of concrete. Find the split tensile strength in MPa. Take depth as 150 mm and length as 300 mm.
Determine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 400mm Thickness of flange tf = 140 mm Effective depth d = 380 mm Effective concrete covering d' = 75 mm Compressive strength of concrete fc' = 30 MPa Yield stress of steel bar fy = 300 MPa Mu = 448 kN-m As = mm2
a. Determine the moment of Inertia at the neutral axis.b. Determine the resisting moment for the cross section shown.c. Determine the stress of steel after concrete hardens.