Answered: 1. Members KJ, KD, CD, and IH 2m L 4 KN…

Engineering

Civil Engineering

1. Members KJ, KD, CD, and IH 2m L 4 KN B 2m 5 kN K C 2m 6 KN D 3m E 1 3m F H 3m 4m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For the truss system shown in Figure 3: a. Sketch a free body diapram showing all forces acting, b.…

A: a. Following is the free body diagram of the given truss:

Q: 2. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming…

Q: Determine the the force in member GJ of the truss and tate if this member is in tension or…

A: Given that : F = 1050 lb Intro : 1- It is asked to determine the forces in member GJ and GC of the…

Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

Q: A 2 m copper bar subjected to a tensile load 180 kN is suspended from a pin that is suppo by two…

A: To find deformation in lower end of copper bar

Q: A bar made of a metal alloy has the dimensions shown in Figure. If an axial force of P=10xb kN is…

A: Axial Force , P = 70 kN = 70×103 N Length of bar, L = 3 m Elastic modulus of the steel , E= 210 Gpa…

Q: For the truss shown below, F= 12 kN and L= 3 m. a) Determine the force in member BE. A and E are…

Q: A homogeneous steel beam is loaded from the figure below. The Cross- Sectional area of the beam and…

Q: 2.47 The negligible weight rigid bar is pinned at O and attached to two vertical rods. W is the…

A: The minimum Value of P is adopted means we take P = 221.072 Kn The rods are assuming stress free.…

Q: The equation of deformation is derived to be y = x² - xL for a beam shown in the figure. L The…

A: Given data- The equation of deformation- y=x2-xL, To Find- The curvature of the beam at the…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: Given data

Q: SN = 83 Problem 2: Refer to the figures below, solve for the force in the marked members in each…

Q: The geometry of the truss that you are to analyze is shown below in Figure 1. The load at joint B is…

A: Since value of theta is not given so reactions are find out in terms of theta values. So that we can…

Q: Determine the forces in all bars of the truss shown in the given figure. Indicate tension or…

A: Given TrussLoading 40, 30, 20 and 18 kNTo find out Member forces

Q: A simply supported planar truss is subjected to point loads at joint B and D as shown in Figure 2.…

A: Find the reaction of the truss calculate θ=tan-113.2710=52.99° and α=tan-113.275=69.35°consider ∑…

Q: The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and…

A: For the given rigid bar,

Q: 1. Three uniform 1-meter bars weighing "W" each are welded together as shown. The bars are suspended…

A: Consider the following free body diagram: The value of TB = 250 N is given in the data. Calculate…

Q: A nswers: a) ₁ = 0₂= (1) i i a C C b MPa MPa (2) D L2

Q: 3. A solid aluminum shaft in 3 in in diameter is subjected to two torques as shown below. Determine…

Q: The bars of the pinned-connected truss shown in Figure below are each 30 mm by 60 mm in…

Q: At an initial temperature of 12°C, the bars are unstressed and was placed between two rigid and…

A: Since the supports are unyielding, temperature increase will tend to expand the bars and no external…

Q: 8. A rigid bar AB is supported by three rods. A load P = 350 kN is applied to the bar. The modulus…

A: To Find :- Deformation in the rods in mm

Q: For the state stress shown in figure below, determine the principle stresses and the maximum…

Q: Q2: The pin-connected structure shown in figure below consists of a rigid beam ABCD and two…

A: My dear Given Area of bars Youngs modulus Point load at B We will use compatibility equations and…

Q: Using method of joints, analyze the following figure if: 0=30°, Q=60°, and d=10 ft 625 lb D 750,lb…

Q: The curvature of the beam at the mid-span

A: Given, Equation of deformation is derived to be, y= x3-xL (shown in figure)Determine the curvature…

Q: Three uniform 1-meter bars weighing "W" each are welded together as shown. The bars are suspended by…

A: To determine: Weight of the bars in kg Tension in the wires at A and C To solve the problem, we…

Q: The truss is made from three pin-connected members having the cross-sectional areas shown in the…

A: Given

Q: 500 D E 250

A: We will use method of section and method of of joints to solve this question

Q: For the lattice shown in the figure below, calculate the forces in all frames. Indicate whether the…

Q: All members of the aluminum truss have the same cross-sectional area. Member AD and CD are made of…

A: Data Given: ∆T = 80° - 20° = 60°Cαsteel = 11.7 × 10-6/°Cαaluminium = 23.1 × 10-6/°CEsteel = 200…

Q: ur solution including units and the free body diagrams. 20 KN 3 m A 10 KN 4 m E 20 KN 4 m D C 10 kN

A: Find the force in each members

Q: The 465-kg uniform I-beam supports the load shown. Determine the reactions at the supports. Answers:…

A: To determine the reaction at support of the Simply Supported beam.

Q: The truss is made from three pin-connected members having the cross-sectional areas shown in the…

Q: A steel bar is subjected to a force F as shown in the figure. This beam is welded to a rigid wall…

A: To find Maximum force F

Q: An aluminum bar having a cross-sectional area of 160 mm carries the axial loads as shown in the…

Q: SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the…

A: In mechanics, axial stress refers to the force acting per unit cross-sectional area in the…

Question

Prove that the trusses shown are statically determinate and solve for the force members required for each item. Show your complete solution with figures.

1.
Members KJ, KD,
CD, and IH
2m
L
4 KN
B
2m
5 kN
K
C
2m
6 KN
D
3m
E
1
3m
F
H
3m
4m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please answer neatly and step by step. thank you. Problem No. 1: Using MCD, determine the reactions and the forces in each of the member of the truss as shown. Member Diameter, mm E, GPa AD 70 200 AC 70 200 BD 70 200 BC 70 200 CD 50 200 80 kN 60 kN 5 m 5 m A E5 m 5 m -
Task 1 The engineering department has developed the following equation for the bending moment of a beam and you have asked to investigate its behaviour M(x)=x²-3x²-4 The Beam is 4m long and the design team suspect the is problem if the bending moment is zero in the range between 3-4m and you have been asked to a) Plot the bending moment at 0.5m interval for the range 0≤x≤4m 0≤x≤4 and determine if the bending moment is zero in range 3m ≤ x ≤ 4m b) Use the graph to estimate where the bending moment is zero c) Use the bisection method to numerically estimate the exact location where the bending moment is zero d) Newton-Raphson method to obtain the required location e) Compare the results of the above method to determine which gives a best solution
Q1- Classify each of the structures shown in adjacent figure as statically determinate, statically indeterminate, or unstable (state the reason). If indeterminate, specify the degree of indeterminacy. A1 (BEAM) Pinned Hinge A5 (FRAME) Pinned Hinge Pinned Hinge A6 (FRAME) A2 (BEAM) Pinned Hinge Pinned Hinge A7 (FRAME) Pinned Hinge A3 (BEAM) APHYYN www A8 (FRAME) Pinned Hinge A9 (Truss) A4 (FRAME) A10 (TRUSS)
Determine forces in members BC, BG and FG
y? dx + (x² + 3xy + 4y²) dy
DETERMINE THE FORCES ACTING IN MEMBERS CD, CH AND BJ. K J I H G 4 ft A B C ID E -3 ft 3 ft 3 ft 3 ft 3 ft → F 1500 lb 1500 lb 1500 lb 1500 lb 1500 lb
A Thin wire of 12mm diameter Placed in a water, the amount of force require to lift the N -) ring (Neglect weight of ring) (~ = 13.2; mt² A 1 dyne B 0.5x105dyne C 497 x 105 dyne D 105 dyne
Q4 For the simply supported beam shown below, what are the support reactions? 8N 5N 3N A B 1m 2m 2m 3m
1-39. Two high-strength steel rods of different diam- eters are attached at A and C and support a mass M at B, as shown in the figure. What mass M can be XX 1500 3600- B Fig. P1-39 -1800- 2400
W1 A OC OD X1 X2 X3 X4 Given: X1 = 8m X2 = 6m X3 = 4m X4 = 6m W1 27KN/m W2 = 31kN/m Moment at Joint A [Choose ] Moment at Joint B [Choose ] Moment at Joint C [Choose ] Moment at Joint D [Choose] Moment at Joint E [Choose ]
Q3: Find the support reactions at A: y 500 mm A P=last 2 student's ID#+100 (N) last 3 student's ID# (mm) 20 mm 55 D B C x last 3 student's ID#+20 mr 40 mm 60 mm
2 of 2 - + 160% Q4-In the below picture, the subject has a spine space implant at cross section A-A and is lifting a box with weight of 100N. The subject's weight (600N) is also acting at the center of mass shown in the picture. a) Determine the internal loadings (only shear force & normal force, don't need to calculate any bending moment) at cross section AA on the spine at the below posture. b) Determine the shear stress due to shear force in the spine space implant with the diameter of 4 cm. c) If the implant is made of a biocompatible material with failure shear stress of 1Mpa, determine the factor of safety (F.S.) 10cm 600N 10cm -----30° 600N 40cm .30 100N 40cm 1.30 100N (Results: V = 350N, N = 606.22N,t = 0.278 MPa, F.S = 3.597) MAR tv 25