1. Mass suspended simple harmonic motion (measured from equilibrium position), displacement, velocity, and acceleration are x = 75mm, 450 mm/s, a = -442.5 mm/s^2. Period of Vibration and the amplitude of motion. 2. A uniform of rod of mass m = 3kg is supported by a pin at its midpoint c and is attached to a spring constant k = 120 N/m. If end A is given a small displacement, and released, determine the T of it resulting motion A k = 120 N/m m = 3kg B

1. Mass suspended simple harmonic motion (measured from equilibrium position), displacement, velocity, and acceleration are x = 75mm, 450 mm/s, a = -442.5 mm/s^2. Period of Vibration and the amplitude of motion. 2. A uniform of rod of mass m = 3kg is supported by a pin at its midpoint c and is attached to a spring constant k = 120 N/m. If end A is given a small displacement, and released, determine the T of it resulting motion A k = 120 N/m m = 3kg B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

VIBRATION ENGINEERING ASSIGNMENT#3 1. What is the equivalent stiffness of the springs in the system? 2. What is the equivalent torsional stiffness of the shafts? -50 cm- Ahminum -20 Steel -15 mm 3. Determine the equivalent stiffness of a linear spring when a SDOF mass-spring model is used for the systems shown. 1 m 1 m E- 200 x 10° N/m² 1- 1.15 x 104 m* 20 kg T. 4. Determine the equivalent stiffness of a linear spring when a SDOF mass-spring model is used for the systems shown. - Massless beam E, I T.
i. À. vehicle wheel, tire, and suspension can be modeled as a SDOF spring nd mass as depicted below: The mass of the wheel and tire is measured to be 300 kg and its frequency of oscillation is observed to be 10 rad/sec. What is he stiffness of the wheel assembly? vehicle frame suspension tire and wheel
Question 1. A body of mass 100 kKg is suspended by a spring of stifness of 30KN/m and a dashpot of damping constant 1000 N.s/m. Vibration is excited by harmonic force ft)=80 cos (67tt) 1- Write the equation of motion of the system using Lagrange's equation. 2- Find the natural frequency and the driving frequency. 3- Write the complete solution of the vibrating system.
Figure 1 shows a system comprising a bar with mass m-12 kg and the length of the bar L=2 m, two springs with stiffness kt=1000 N-m/rad and k = 2000 N/m, one damper with damping coefficient c=50 N-s/m and two additive masses at the end of the bar, where each mass (M) is equal to 50 kg. The rotation about the hinge A, measured with respect to the static equilibrium position of the system is 0 (t). The system is excited by force (F) so find the state space representation of the system if the output y=ġ(t).
A 1.5-kg mass attached to an ideal massless spring with a spring constant of 20.0 N/m oscillates on a horizontal, frictionless track. At time t = 0.00 s, the mass is released from x = 0.0 cm with a velocity of 0.370 m/s to the left. Find the followingA. Time periodB. Total mechanical energy of the massC. AmplitudeD. Phase constant of motion. Discuss the two possible values of phase constant you get and explain how you arrived at the correct answer. Write the equation of motion.E. Maximum acceleration of the mass. (Acceleration is maximum when it ispositive). How long after the release does the maximum acceleration occur?F. Draw the position-time graph for one cycle of motion.
A single degree of freedom mass-spring-damper system is subject to vibration under the influence of a harmonic force. On my site, it is given as m=2 kg, k=800 N/m, c=64 Ns/m. The amplitude of the harmonic force is F0=256 N and its frequency is w= 20 rad/s. Answer the questions in options a, b, and c according to the given information. 1) Calculate the damping ratio of the system (ξ) a.1 b.0.7 c.0.9 d.0.8 2)Calculate the magnification factor (M) of the system. a.0.86 b.1.25 c.0.312 D.0.625 3-) Calculate the maximum vibration amplitude (X) (meters). a.0.2 b.0.1 c.0.4 D.0.3
1. A .6kg block is hung from a spring with a force constant of 25 N/m. Calculate the displacement of the spring from its equilibrium length, assuming it is hung vertically and neglecting the spring mass. 2. The mass in (1.) is pulled downward by an additional 6 cm and held steady. Calculate the potential energy input corresponding to this additional displacement. 3. Calculate the period of oscillation of the mass/spring system once the object is released. 4. Write an expression for the vertical motion of the system, along the y (vertical) axis, in the form: ?(?) = ? cos(?t) (Use the appropriate values of A and ω in your expression). 5. Calculate the maximum speed of the oscillating object and its maximum kinetic energy. Do your results make sense based off what you got in 2? (I posted all 5 parts but could you answer only 4 and 5? Thank you!)
I need hand written solution only otherwise | will down vote
Consider a spring-mass system with mass equal to 1 kg, spring constant equal to 25 Newton/meter.Which damping constant b causes critical damping?If the damping constant b in the above system is set to 3 N ∙ sec/m, then what can be said about the number of timesdoes the object pass through its equilibrium position?If the damping constant b in the above system is set to 8 N ∙ sec/m, then what is the interval of time between thesecond time the object returns to its equilibrium position and the third time it returns to its equilibrium position?
PART A k = 2.000 N/m M=0.125kg A 0.125kg mass is attached to a horizontal spring of spring constant k = 2 N/m and set into ocillation. Assume frictionless floor. 4 rod /s What is the angular frequency w of the vibration? o = How about the vibrating frequency f in Hz? f = 0.64 Hz. The position of the mass is given as x = A cos (ot + o). With your calculated value of w, fill in the following table (don't forget to set your calculator to "radian mode"). Each row represents a different oscillation with the same spring, pay attention to sign: v (m/s) .092 -.14 a (m/s²) 3076 -32 -.8712 -.64 A (m) t (s) x (m) -.02 F (N) .04 -.04 фо (rad) 0.03 2.5 0.3 - 212 1.36 0.04 0.02 0.2 0.06 .0545 0.1 0.4 .076 1.08 -. 08 0.04 0.3 |-26 - .25 2.94 -0.2 0.5 0.04 0.1 0.1 PART B Each of the rows in the following table represents an oscillation of a different spring and mass. Fill in the blanks. E is the total energy. Vmax, v, Xmax, and x are all positive in values. A (m) Vmax Xmax m (kg) k (N/m) E (J) x at…
Q.2 Two springs, damper and a mass are attached to a rigid, weightless bar PQ as shown below. Write the equation of motion of the system using D'Alemberts principle. Find the natural frequency of vibration of the system. J6+ (kde) ds. C 0000 m
Q.2 Two springs, damper and a mass are attached to a rigid, weightless bar PQ as shown below. Write the equation of motion of the system using D'Alemberts principle. Find the natural frequency of vibration of the system. J6+ (kdo) de. C 0000 m