1. Find the average value of current when the curren that are equidistant are 4A, 5A and 6A.

Q: The voltmeters in the figure measure RMS voltages. If V, = 23 V and V, = 14.5V what is V3? R V V3 23…

A:

Q: From the given Ammeter diagram, the span is -- A. J0407 A a. -1 O b. 4 О с. 3 o d. -1 to 3

A: Given, Ammeter diagram

Q: Given the Figure 3 as shown below, determine: R a) Draw the Phasor diagram in terms of: 250 2 1.…

A:

Q: Calculate the output voltage for the circuit given. The value of input voltage can be taken as 2mV,…

A:

Q: What is the number of electrons in the C.B., if their number is (7) in the V.B. at 0 °k?

A: Since there is no conduction at 0 kelvin as there is no bandgap energy. Thus the electron in the…

Q: ave winding is suitable for voltage and enerator. D low, high O high, high low low

A: Two type of windings are used in DC machines. 1. Lap 2. Wave

Q: The segment of a waveform below the zero reference line is the negative or the negative

A: Waveform- The term waveform is define as the graphical or diagrammatic representation of the…

Q: What is the peak to peak value of sinousoidal voltage having average value of 100 V ?

A: Given: A sinusoidal voltage having average value of 100 V Vavg=100 V

Q: calculate the magnitude of the current through the j3.3k ohm inductor. jl k2 1.2 k2 -j4.7 k2 j2.2 k2…

A:

Q: For the given waveform, current the voltage by an angle, þ. cot

A: we need to fill the given blanks.

Q: A double beam oscilloscope displays two sine waveforms A and B with peak to peak heights as A14 4 cm…

A:

Q: What would happens if the diod was't ideal, rather it was Si ?

A: It is given that:

Q: For the given waveform, the current the voltage by an angle V ot (rad) T/2

A: From the given waveform , we can easily found which one leading or lagging.

Q: A double beam oscilloscope displays 2 square waveform  G and  H.  The time/cm switch is on  50 ms/cm…

A: Dual CRO

Q: What is the magnitu de oF a pornt charge that would create an ele cric pield Of 1-00 Nlc at poin t…

A: It is given that: E=1 N/Cr=1 m

Q: The ratio of % reactance at rated kVA to the % reactance at base kVA is equal to

A: We need to tell the correct option for the given blank in the given statement.

Q: ac = 250 mnH if

A: To find the equivalent inductance across the terminal a-b

Q: Value of series impedance if inductance is 4mH , resistance is 40 ohm and frequency is 50 Hz.

A: Given values are =

Q: 2.17 Find the average value of each voltage in the following figures: 5 V 100 V OV- OV- (a) (b) 20 V…

A: b)  Given; The waveform is Here, the sinusoidal signal is full wave rectified Vm=100 V So average…

Q: The following figure indicates alternating(ac) quantity. SQuare wave Select one: O True O False

A: The definition of an alternating quantity may be defined as a quantity which  reverses its direction…

Q: calculate the magnitude of the voltage drop across the jik ohm inductor 1.2 k2 jl k2 -j4.7 kQ j2.2…

A:

Q: At what frequency will a 0.016 henry inductor have an inductive reactance of 80 ohms?

A:

Q: 20sin (377t) L Em sin wt i = (jwL) Emz0° i WL290° Em 90°

A:

Q: A sine wave with 2 VP will have Vrms as

A:

Q: In Class A chopper, if duty cycle is varied from 0 to 1, the output voltage will vary from zero to…

A: In this question, choose the correct option What is output voltage variation if duty cycle carried…

Q: Typically, the voltage of the field system in an alternator is

A: Typically the voltage of the field system in an alternator is LESS THAN 200 V.

Q: Determine the maximum peak-to-peak ripple current of previous problem by using the next equations,…

A: To determine the maximum peak-to-peak ripple current ((Imax​)), we can use the given equations.…

Q: Homework1 A waveform has a frequency of 100 Hz, and has an instantaneous value of 100V at 1.25 msec.…

A: Given data, f = 100 Hz. t = 1.25 ms. V = 100 V.

Q: A DC voltage has an average value of 68v what is the rms value

A: DC is constant voltage.

Q: 4. After MOV AL, A0H DAA AL=

A: After the mov operation, AL will carry A0H.

Q: 4. A 10 resistance in parallel with a 20 resistance provides a combined equivalent resistance of a)…

A: Given: 1Ω and 2 Ω resistance are in parallel. To find: Equivalent resistance.

Q: In single phase fully controlled converter, if the ripple factor is 1 then the form factor of the…

A: relation between the form factor and ripple factor is   ripple factor = form factor2-1 given ripple…

Q: 11. Square the quantities 15/25°, 8/-34°, 16/90°.

A:

Q: A sine wave with 2 V, will have Vrms as p

A:

Q: Tu netuork show in opeating in the thndy doulce. If V, = 2aes2t state wilh sinusoidal ve and V, 2…

A:

Q: If values of any quantity vary with time 't' are plotted to a base of time, then the resulting graph…

A:

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.