1. Explain the Reason to evaluate the Qo max when Pwf-0, is that applicable? explain? 2- Explain the reason to calculate the value of equivalent depth for pwf from working chart. 4. Explain which part from the well, that the inflow performance relationship (IPR) describes and Vertical lift performance (VLP)? Give an example for each performance.

1. Explain the Reason to evaluate the Qo max when Pwf-0, is that applicable? explain? 2- Explain the reason to calculate the value of equivalent depth for pwf from working chart. 4. Explain which part from the well, that the inflow performance relationship (IPR) describes and Vertical lift performance (VLP)? Give an example for each performance.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.7CTP

See similar textbooks

Similar questions

b) While computing the bending moment and the shear force on the side walls of the spillway chute showed in Figure 1, a structural engineer assumed that the water pressure varies linearly from zero at the free surface to pgy at the invert of the chute, in which y flow depth measured vertically. What are the computed values for the bending moment and shear force at the invert level? Are the computed results correct? If not, compute the percentage of error. Side wall Water surface 50 m Section:A-A 30 Figure 1: Spillway Chute
Give me right solution You have designed a 16-in diameter stormwater pipe to flow at a velocity of 5 ft/s when full. The Manning’s roughness coefficient is 0.011. What material is most likely the pipe made of and what is the slope of the energy grade line?
The cross section at station 2+60 has a cut area of 9 ft² and a fill area of 4 ft² and the cross section at station 3+00 has a cut area of 7 ft² and a fill area of 8 ft². What is the volume (yd) of fill between these stations? Assume 10% swell. Round to the nearest hundredths. Response Feedback: V=L fill A 2+60 +A 3+00 54 Swell means the cut material expands, therefore less fill is needed. The swell amount is subtracted from the calculated fill volume.
Which of the following are positive kick indicators? a. Unexplained pit gain b. An increase in the return flow of mud with the mud pumps off c. Well flows after mud pump has been turned off d. All of the above e. None of the above
Refer to Problem 11.7. Given: cv 2.8 106m2/min.How long will it take for 60% consolidation to occur?
A DrahmedsoilMechanicsnoteschapters pdf Downloads/DrahmedsoilMechanicsnoteschapter5.pdf 5.16 Refer to Figure in which upward seepage is taking place through a granular soil contained in a tank. Given: H1 = 1.5 m; H2 = 2.5 m; h = 1.5 m; area of the tank = 0.62 m?: void ratio of the soil, e = 0.49: G. = 2.66; and hydraulic conductivity of the sand (k) = 0.21 cm/sec. a. What is the rate of upward Valve fopen) seepage? b. Will boiling occur when h =1.5 m? Explain. c. What would be the critical value of h to cause boiling? Inflow Ans.: (a) q = 781.2 cm'isec, (b) No. (c) h = 2.77m 5.17 Refer to Figure of Problem 5.16. If H, = 0.91 m, H2 = 1.37 m. h =0.46 m, Ysat = 18.67 kN/m, area of the tank = 0.58 m2, and hydraulic conductivity of the sand (k) = 0.16 cm/sec, a. What is the rate of upward seepage of water (m/min)? b. If the point C is located at the middle of the soil layer, then what is the effective stress at C? Ans.: (a) i= 0.336, (b) q = 0.0187 m/min 5.18 A cut is made in a stiff,…
9.14. Oil of viscosity 0.48 Pa-s and specific gravity 0.90 flows with a mean velocity of 1.5 m/s in a 0.3 m pipeline. Calculate shearing stress and velocity 75 mm from the pipe centerline.
A concrete pipeline is installed to deliver 6m3/sec of water between two reservoirs 17km apart, if the elevation difference between the two reservoirs is 12m, determine the required pipe size, if friction factor, f of Darcy-Weisbash h equation is 0.0135.
A 600 mm diameter horizontal pipe with a length of 1500m and C=120. the pressure gage attached downstream of the pipe reads 16kpa and another gage is attached upstream of the pipe reads 30kPa. If another gage is attached between the ends of the pipe. What is the total head loss?
Example:- check the stability of shown gravity dam if you knew that there is an effect of earth quake with k, = 0.1, ku = 0.12 The vertical acceleration is downward and the horizontal is toward reservoir = 0.75,Yw = 1 (Ton/m ), Ycon. = 2.4 (Ton/m^3) Ysubmerged silt= 1.36 (Ton/m') Y silty water1.925 (Ton/m') Wind velocity = 120 (km/hr) With straight length of water. expanse = 35 km , ka=0.3,
Example:- check the stability of shown gravity dam if you knew that there is an effect of earth quake with k, = 0.1, ku = 0.12 The vertical acceleration is downward and the horizontal is toward reservoir = 0.75,Yw = 1 (Ton/m ), Ycon. = 2.4 (Ton/m^3) Ysubmerged silt= 1.36 (Ton/m') Y silty water1.925 (Ton/m') Wind velocity = 120 (km/hr) With straight length of water. expanse = 35 km , ka=0.3, all kinds of combination
A concrete pipe 750 mm in diameter is laid to a gradient of 1 in 200.The estimated value of Manning’s ?is 0.012m−1/3s.Calculate the discharge when:(a)the pipe is full;(b)the depth is 90% of maximum.Explain why the answer in (b) exceeds th