Gear A with radius 0.018 m is moving with velocity wn = 0.12 rad/s clockwise, with a constant angular acceleration aa = 0.07 rad/s?. B and D are rigidly attached to eachother and the radius of B is 0.24m and the radius of D is 0.09m. The weight of the block Cis 191 Newtons.Determine the time in seconds that it takes block C to move up 9 meters.Also answer the following at exactly that time:1. Draw the complete and clear FBD of the block C. Indicate two sides of the FBD with all forces and mass x accelerations, label all of them.2. Find the velocity of point P and find the acceleration of point P that belongs to B3. Find the number of rotations of B.4. Find the acceleration of C; then, determine the tension in the rope from the FBD of C.

Answered: Image /qna-images/answer/6a707564-cfcd-4bf5-ab60-45445a29722c.jpg

1. Draw the complete and clear FBD of the block C. Indicate two sides of the FBD with all forces and mass x accelerations, label all of them. 2. Find the velocity of point P and find the acceleration of point P that belongs to B 3. Find the number of rotations of B. 4. Find the acceleration of C; then, determine the tension in the rope from the FBD of C.

1. Draw the complete and clear FBD of the block C. Indicate two sides of the FBD with all forces and mass x accelerations, label all of them. 2. Find the velocity of point P and find the acceleration of point P that belongs to B 3. Find the number of rotations of B. 4. Find the acceleration of C; then, determine the tension in the rope from the FBD of C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the constraint acceleration equation between block A and B (Assume all upper and down pulleys' centrals are horizontal).
Question 1: Consider the system below. At the moment shown, all three blocks are at zero velocity (Fig.1). At the same time a a force (F) of 10N is applied as shown to the grey Black (G). Each block has a mass of 1Kg. Shortly after the force, F, is applied, calculate the following: A. What is the acceleration of the red Block R, with respect to the ground (assume ground is the inertial frame). B. What is the acceleration of the red Block R, with respect to Block B. C. What is the acceleration of the blue Block B, with respect to the inertial Frame (ground). D. What is the acceleration of the grey Block G, with respect to the inertial Frame (ground). E. What should have been the magnitude of force F, such that block R would not move at all with respect to the ground. B 30° G Figure 1: Three-block setup
The plumb line of a 2m pendulum describes an arc of a circle in a vertical plane. If the tension in the string is 2.5 times the weight of the bob for the position shown in the figure, find the velocity and acceleration of the bob at that position.
Q4 / 1. For the force system shown in ( fig.4) below the resultant ; (R) is equal to ( 500N) , the angles( a ) and (ß) are ; (25°) and (55° ) respectively ; Determine the value of the component (P) R=500N a= 25° Fig. (4)
IF A=is equal to 7kg and B=4kg ,and theta is 35 degrees Find the acceleration of the blocks and the force in the rope
From the following system, obtain the force components for the system X∗ and Y∗ in terms of i and j. It is known that for the system y and x the value of the force components is F = (F76 N i - F500 N j) N . Solve by any analytical method. (use the values on the image (pea1) not the values on image (pea2))
Complete solution please thank you
ATWOOD'S MACHINE Draw a free body diagram of m1 and another free body diagram of m2. Using these diagrams, apply Newton’s second law to each mass. Assume that the tension is the same on each mass and that they have the same acceleration. From these two equations, find an expression for the acceleration of m1 in terms of m1, m2, and g. Compare the expression to your result in Step 5 of Analysis.
EXERCISE 3.40 Collar C slides relative to the curved rod at a constant speed u. The rotation rate about bearing axis AB is constant at Q. Determine the acceleration of the collar in terms of the angle locating the collar. Also derive expressions for the dynamic forces exerted on the collar by the rod and the tangential force required to hold u constant. Gravity may be assumed to be unimportant. (Hint: attach frame xyz to the curved rod, make the tangent point of AB and circle as its origin. Axis x is horizontal and rightward. y axis is vertical and downward.) 225
I can't figure Part A