1. Determine the estimated rainfall at ungauged site using Inverse Distance Weighting method. ARG1 = 8mm, ARG2 = 9mm, ARG3 = 12mm, ARG4 = 11mm, ARG5 = 13mm From Ungauged to ARG1 ARG2 ARG3 ARG4 ARG5 Distance (km) 38 29 35 41 27

1. Determine the estimated rainfall at ungauged site using Inverse Distance Weighting method. ARG1 = 8mm, ARG2 = 9mm, ARG3 = 12mm, ARG4 = 11mm, ARG5 = 13mm From Ungauged to ARG1 ARG2 ARG3 ARG4 ARG5 Distance (km) 38 29 35 41 27

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The ultimate load carrying capacity of a short circular column of 300 mm diameter with 1% helical…

Q: Question- A body is subjected to a tensile stress of 1200 MPa on one plane and another tensile…

A: Tensile stress Stress in y-direction Shear stress To Find-The value of the maximum normal stress.

Q: A hollow, circular, steel column (E = 30,000 ksi) is subjected to a compressive load P. The column…

Q: A 30-cm by 15-cm Venturi meter is installed in a vertical pipe, as shown below. The flow is upward…

Q: Glycerine having dynamic viscosity, μ = 1.5 Pa.s and density p = 1260 kg/m³ flows at a velocity of…

A: Given data in question Dynamic viscosity 1.5 Pa sDensity 1260 kg/m3Velocity 10 m/sDiameter 15 cmTo…

Q: Please select the correct word to complete the sentence Part A) A ["pulley","cable"] is an example…

A: Some statements regarding structural components and members. We need to choose correct option to…

Q: A 6-m simply supported singly reinforced concrete beam is 400mm wide and effective depth of 500mm.…

A: f'c = 20.1 Mpafy = 283 MpaBeam span = 6 mb = 400 mmd = 500 mmAs = 8*510 mm2Total dead load = 18…

Q: Draw the shear force and bending moment diagrams of the beam whose span and loading condition are…

A: To draw the shear force for any beam we consider the equilibrium condition and find the reaction for…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: Each square grid = 400 psi

Q: The crank OA is shown. If OA = 66 mm, 0 = 55°, and 3 = 60°, determine the moment of the force F of…

Q: In a canal irrigation project, 62% of the culturable command area remained without water during…

A: 62% of the culturable command area (CCA) remained without water during Kharif season,73% of CCA…

Q: (a) Discuss the suitability of using either concrete, steel or timber to construct the structure in…

A: Concrete is a commonly used material in construction due to its strength, durability, and fire…

Q: A reservoir has a catchment area is about 150 hectares. The rainfall is 2.5times of run-off and the…

Q: In a Marshall sample, the bulk specific gravity of mix and aggregates are 2.424 and 2.644…

A: Bulk specific gravity of mix Gm=2.424Bulk specific gravity of aggregate =2.6447% of…

Q: Problem 3 Determine the vertical displacement at point B. Use the method of virtual work. El is…

Q: b) The frame is loaded and supported as shown in Figure Q4b. (1) Draw the free-body diagrams of the…

A: As per Bartleby's guidelines we are supposed to answer only first question.Kindly repost other…

Q: Determine the degree of indeterminancy of plane frames as shown in the figure Pls answer problem 1&2

Q: s to be pin joints and set P = 145 lb, L = 11 ft, and x = 3.9 ft. A E D i 42° L F lb B C L

Q: The principal stresses at a pc perpendicular planes are 76 and 34MN/m² (tensile). Find t tangential…

Q: The internal shear force V at a certain section of an aluminum beam is 8.2 kN. If the beam has the…

Q: A vibrating system is characterised by the following parameters: Mass = (m) = 6 kg Stiffness of…

Q: A three-hinged symmetrical arch is loaded as shown in figure. Which one of the following is the…

Q: A wooden floor is required to carry load of 12kN/(m^2) and is to be supported by wooden joists of…

A: We have to find the spacing of the joists

Q: If the transversal Ultrasonic Pulse Velocity of a concrete mixture was measured as 2700 m/s, and the…

A: Transversal velocity (Vs) = 2700 m/s Specify gravity (S) = 2.4 Poisson's ratio = 0.2 Determine the…

Q: 8. Define psychrometry.

A: To define:The term psychrometry.

Q: Instead of merely connecting lines, designers may use the full potential of solid modeling to give…

A: Solid modeling is a CAD approach that enables designers to produce three-dimensional (3D)…

Q: 30 50. 50 50 30 -O --O O |50|50 M16 bolt 210 mm (all dimensions are in mm) Chain Bolting T

Q: 3. Considering sag rods and tie rods at midspan, what is the interaction value for combined moment?…

Q: A simply supported beam is loaded as in figure. The bending moment at C is 4 KN 4 kN-m A 2m с 2m- 4…

Q: (ii) The minimum and maximum dry unit weight of a sand were found to be 14.71 and 16.68 kN/m³,…

Q: Review the importance of FIDIC (International Federation of Consulting Engineers), the Manual of…

A: The International Federation of Consulting Engineers (FIDIC), a well-known organisation with a focus…

Q: Solve for the EIA using Area-Moment Method. 3m 50 kN B 2m EID@ pt. B 60KN dic 2.5m 荔

A: EI = Constant Determine the deflection at point-B using Area moment method.

Q: The figure below summarizes the three different approaches for BMD. Using your own words explain all…

A: Approach 1 (Volumetric design with performance verification):Approach 2 (Performance modified…

Q: A crop is to be grown, for the month of December. If the effective rainfall in that month is 1.7 cm,…

Q: Five different particle sizes are mixed in proportions shown below and water is added to make the…

Q: Determine the force in member AD of the pin-connected truss. AE is constant. Use the Force Method.…

A: A truss is hinged at E and the roller is supported at B.The truss is loaded with 5kN, 20kN, and 12kN…

Q: 1.4 A water supply reservoir has an annual capacity of 25 x 10' acre-ft. It is serving a city with a…

Q: For the propped cantilever shown in the figure, a hinge is provided at C. A and B are at the same…

Q: The chute is used to diver The water has a cross-se weight of the chute and w P=1 Mg/m³. (Figure…

Q: A wooden floor is required to carry load of 12kN/(m^2) and is to be supported by wooden joists of…

Q: In a parabolic vertical curve, the rising grade g_{1} = 0.8% and the falling grade g_{2} = 0.7%. The…

A: g1 = 0.80%g2 = -0.70 %Rate of change of grade(r)r = 0.05%Find the length of vertical curve

Q: A crew consisting of two carpenters and one helper can fix 10 m² of a slab form work in 8 hours and…

A: Given data:A crew consisting of two carpenters and one helper can fix 10 m2 of a slab formwork in 8…

Q: ). Find the bending moment at 4 (M4) ■). Find rotational displacement at 2(0₂) El=10 000tm² NOTE:…

A: Given a frame loaded at joint 2.Required : the member end moment at 4 in member 2-4 and the…

Q: Exercise 2.8.1. Determine the minimum snd maximum stress intensities in a short cast iron hollow…

A: A short hollow circular column,D= 300mmd= 250mmP = 60kN = 60000NEccentricity = e= 300mm

Q: Water flows in a trapezoidal channel with side slope 1V:3H, bottom width of 16ft and water depth of…

Q: A rectangular 230 mm 350 mm beam is (effective depth). The factored shear force acting at a section…

A: Given-Rectangular beam Factored shear force-Permissible shear stress We have to find the design…

Q: Given the following elements of a T-beam: Flange width bf= 900 mm, Flange thickness t= 1100 mm,…

A: Flange width bf= 900 mmFlange thickness t= 1100 mmWidth of web bw= 310 mmEffective depth d= 460…

Q: Calculate the vertical displacement of the beam midpoint of the system given below. 50kN Yanıt: 31 *…

Q: How long will it take for 50% of the total settlement to occur in laboratory specimen of the clay…

A: Degree of consolidation = U= 50%Cv= 0.25m²/dayDiameter of specimen = 6.35cmH= 2.54cm

Q: Suppose two ball bearings (A and B) are constrained to move in the horizontal plane along concentric…

Concept explainers

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.

Question

1. Determine the estimated rainfall at ungauged site using Inverse Distance Weighting method. ARG1 = 8mm, ARG2 = 9mm, ARG3 = 12mm,
ARG4 = 11mm, ARG5 = 13mm
From Ungauged
to
ARG1
ARG2
ARG3
ARG4
ARG5
Distance
(km)
38
29
35
41
27

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data:-

VIEW

Step 2: Determining the rainfall at ungauged site by using inverse distance weighting method:-

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the estimated rainfall at ungauged site using Inverse Distance Weighting method. ARG1 = 5mm, ARG2 = 12mm, ARG3 = 15mm Stations Ungauged - ARG1 Ungauged - ARG2 Ungauged - ARG3 ARG1 - ARG2 ARG2 - ARG3 Bearing N 45° E N 75° E S 30° E S 40° E S 40° W Distance 20km
9. Over a period of 7 months, record collected. One site gauge “A" analysis technique to carry out shown in the table below: daily rainfall data have been inspected. Use the double mass following operations using the data date of the first significant change of a) Determine the approxim Gauge “A" readings. c) Evaluate a correti d) Apply the corr readings. atio that can be used to adjust incorrect values. on process on the incorrect values to get the correct Reading "Gauge A" Reading "others" Month 1 200 340 Dr. Wael Elrammoame 2 220 410 3 140 251 4 90 312 5 72 264 6. 55 210 7 47 180 excel drawing
What will be rainfall intensity of 5 yr-rainfall of duration 1 hr. if following details are given : 5.82, x = 0.16; a = 0.4; n = 0.75 [1.40.75 1.287; 50.16 1.29] K = = =
Unit hydrographs derivation (UHD) is to develop storm hydrographs due toactual rainfall event over watershed. There are TWO (2) methods used todetermine UHD, namely convolution and deconvolution method. Describe thedifferences between these TWO (2) methods
b) An analysis is to be undertaken to check whether there is a need to add more rainfall stations in a sub-basin. Explain the analytical method that can be used, са and the data required to compute the number of additional rainfall stations if it is desired to limit the error in the mean to 10%. Use these equations to assist 100xơm-2 explanation N = ? and C,
b. There are five rainfall gauges on a square plot of land of dimensions 2km x 2km. One of the gauges is located in the centre of the plot. Determine the position of the other four rainfall gauges such that the areal rainfall estimated using the Thiessen Polygon method is exactly equal to the estimate using the arithmetic method. Show your approach for finding the positions. Also show the gauge positions on a sketch.
For the basin shown in Fig. 1, the normal annual rainfall depths recorded and the isohyetals are given. Determine the optimum number of rain-gauge stations to be established in the basin if it is desired to limit the error in the mean value of rainfall to 10%. Indicate how you are going to distribute the additional rain-gauge stations required if any. What is the percentage accuracy of the existing network in the estimation of the average depth of rainfall over the basin? The area between the isohyetals are given below:
A-One of four monthly reading rain gages on a catchment area develops a fault in a month when the other three gages record, respectively (37, 43, 51)mm. If the average annual precipitation of these three gages are (726, 752, 840) mm, respectively and (694mm) of the broken gage. Estimate the missing monthly precipitation at the later station. B-On a certain river, the following data obtained by stream gage: Water stage(m) Flow rate(cumecs) Main staff Auxiliary staff 122 121.5 400 122 120.5 680 Estimate the flow rate when the main staff read (122m) and the auxiliary staff read (121.1m)? C-The following table represents the relation between the recorded discharges and the water levels. Estimate the following relation and find Q when H=15m. Q=a (H-2) b 10 20 40 100 Q(m³/s) H(m) 5 7 9 10
Determine the estimated aerial rainfall using Arithmetic Mean method. ARG1 = 8mm, ARG2 = 9mm, ARG3 = 12mm, ARG4 = 11mm, ARG5 = 13mm
Q3) A river basin contains 6 rainfall stations with the annual data given in the table below. How many rainfall stations should be added to the basin to reach an error percent of 8%? Station A B F Annual Rainfall 230 400 301 268 196 351 depth (mm)
4. Rainfall values observed at different points on a watershed (12.5 km?) are shown in Figure 4.14. Compute the mean rainfall using the Thiessen method. 80 tog 105 11 90 I 10 12 13 Scale: 0.5 1.0 km FIGURE 4.14 Thiessen polygon method for computing the mean areal rainfall for Problem 4. 1.5842 0.1697 1.4208 0.9565 1.3765 1.2288 1.6282 0.9001 7 1.8949 0.3467 0.4347 10 0.1961 0.3617 12 13 Scale: 00.5 1.0km
The watershed of a stream has five rain gauge stations inside the basin. When thiessen polygons were constructed ,three more stations lying outside the watershed were found to have weightages. The details of Thiessen polygons surroundings each raingauge and the recording of the rainaguges in the month of July 2012 are given belowRaingauge stationsABCDEFGH Thiessen polygon area(km2)720138014401040900022204191456 Recorded rainfall in mm during july 201213514313712810211599101 Stations B,D and F are outside the watershed. Determine the average depth of rainfall on the watershed in july 2012 by i) Arithmetic mean method ii) Thiession mean method.( (Apply