1. Design a circuit that fulfils the following conditions; a) The circuit has 4 independent loops with four (4) power sources which are connected at different branches. b) The circuit has one (1) dependent current source and one (1) dependent voltage source with both are voltage-controlled type. c) The circuit has one (1) independent voltage source and one (1) independent current source with specified values. d) Two (2) of the power sources (one dependent source and one independent source) have a series connection with a resistor. e) The circuit has Supernode and Supermesh conditions. 2. By assigning some values to the all circuit elements, present a step-by-step calculation to find the voltage, current and power at one of the passive element of your choice in the circuit. Use both Nodal and Mesh circuit analysis technique to validate your answer. 3. Show that the power supplied is equal to the power absorbed in the circuit.

1. Design a circuit that fulfils the following conditions; a) The circuit has 4 independent loops with four (4) power sources which are connected at different branches. b) The circuit has one (1) dependent current source and one (1) dependent voltage source with both are voltage-controlled type. c) The circuit has one (1) independent voltage source and one (1) independent current source with specified values. d) Two (2) of the power sources (one dependent source and one independent source) have a series connection with a resistor. e) The circuit has Supernode and Supermesh conditions. 2. By assigning some values to the all circuit elements, present a step-by-step calculation to find the voltage, current and power at one of the passive element of your choice in the circuit. Use both Nodal and Mesh circuit analysis technique to validate your answer. 3. Show that the power supplied is equal to the power absorbed in the circuit.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. A voltmeter with resistance 'Ry' is connected in parallel with resistance R=150 ohms. The applied voltage V= 175V. Determine the error (E) & percentage error (%E) in the measurement of voltage (V) due to loading effect of voltmeter when-(i) Ry =2.75M 2 V
An independent current source while providing a fixed current having Select one a. Zero voltage across its terminals. b. Not applicable to measure voltage across it. C. None of the above. d. Unknown voltage acrosS ts terminals
a. An electrical engineer was given a contract to design a device with the following specifications: a source voltage of 240 volts and three resistors with 102, 202 and 302 marks on them respectively. This engineer subcontracted this job to you, and instructed you to connect these resistors in series and then in parallel. With your knowledge in circuit analysis; Determine the values of the resistance and the current in each scenario.
An independent current source while providing a fixed current having Select one: a. Unknown voltage across its terminals. b. Not applicable to measure voltage across it. c. Zero voltage across its terminals. d. None of the above.
A galvanometer has resistance 5 ohm and full scale deflection 20 milliampere. Calculate the value of the maximum current when a shunt of 0.1 ohm is connected to its coil. Also, calculate the value of the potential multiplier which is to be connected to the galvanometer to make it a voltmeter that reads up to 5 volt.
Justify the reason, why the true value of a circuit is changed into reduced measured value because of the insertion of a meter for measuring the true value. Mention how it will affect measurement in voltmeter with necessary drawings. Also, Suggest one method to reduce the effect.
A dc voltmeter was designed using direct method with d'Arsonval www meter of full scale deflection of 0.001 A. The third range is 40 V. The values of series resistances are 7.5 KO, 14.5 KO, and 39.5 KQ. Find the other ranges.
Current Mirror In Figure 1, If the two NMOS have the same parameters and the resistors are the same, what current will the ammeter measure [RP3]? Vdd _bias Vdd I_bias R R R Vout A Ammeter М1 M2 М1 M2 Figure 1: Current Mirror with Ammeter Figure 2: Current Mirror without Ammeter If the ammeter is removed (Figure 2), how would you confirm whether the current in the right branch is equal to I given that V V dd' out R is known, and that two NMOS are the same [RP4]? bias In Figure 2, express V in terms of V out R, n, and I, bias if M2 is n-parallel relative to M1 [RP5]. dd
A voltmeter reading 60 V on its 100 V range and an ammeter reading 10 mA on its 30 mA range are used to determine the power loss in a resistor. Ammeter is guaranteed to be accurate within 2.5% and voltmeter is guaranteed to be accurate within 1.5%at their full scale deflection. i. Calculate the % limiting error current. ii. Calculate the % limiting error voltage. iii. Calculate the limiting error of the power.
b) Assume that all lamps are identical. In this condition from your opinion which lamp(s) having more brightness, and which Lamb(s) will be low brightness as shown in figure2. A B E VT Figure 2
please solve all 4 parts Part A Find i for the circuit. Part B Find the power supplied by the voltage source. Part C Reverse the polarity of the voltage source in the circuit shown in the figure, and find i for a new circuit. Part D Reverse the polarity of the voltage source in the circuit shown in the figure, and find the power supplied by the voltage source for the new circuit.
A scientist working under emergency conditions at a jungle based lab realizes that her primitive radio has shorted in the rain and burned out a resister. She wants to match the original resister of 2.50 Ohms but believes that a resistance between 2.25 - 2.75 Ohms would be sufficient. All she has to work with is a spool of fine lead soldering wire and some scrap equipment. a) The wire has a diameter of 1.5 mm and the resistivity of lead is 22*10-8Ohm-meters. How much lead wire would she need to make the resister? b). Looking around the lab she is able to scavenge two 3.5 ohm and one 1.0 ohm resisters from old equipment. Using these three resisters how close can she come to building a 2.50 ohm resister? Explain the optimal configuration and calculate the equivalent resistance.