1. Compare the performance in terms of their efficiency the common base, common emitter, and common collector BJT configuration2. Discuss the two graphs given below and compare their difference between the two figures belowFigure A.Mc (mA)876532IONCE90 μA80 μA70 μA60 μA50 μA40 μA30 μA(Active region)1015(Cutoff region)ICEO BICHO20 μA10 μA1g = 0 MA20 VCE (V) Figure B76321Active region (unshaded area)7 mA6 mA5 mA4 mA3 mA2 mAI= 1 mAICOICRO↓Ig=0mAt0VCB (V)-1102030Cutoff regionBV CROFIC. TO2. Research and discuss the one actual application for each of Bipolar Junction Transistor Configuration; Common Base, Common Emitter, Common Collector3. Provide your references and resources(mA)040

Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

1. Compare the performance in terms of their efficiency the common base, common emitter, and common collector BJT configuration 2. Discuss the two graphs given below and compare their difference between the two figures below Figure A. Mc (mA) 8 7 6 3 2 1 ONCE 90 μA 80 μA 70 μ.A. 60 μA 50 μA 40 μA 30 μA (Active region) 10 Ico BIcao 20 µA 10 μA 1 = 0 με 15 (Cutoff region) 20 VC (V)

1. Compare the performance in terms of their efficiency the common base, common emitter, and common collector BJT configuration 2. Discuss the two graphs given below and compare their difference between the two figures below Figure A. Mc (mA) 8 7 6 3 2 1 ONCE 90 μA 80 μA 70 μ.A. 60 μA 50 μA 40 μA 30 μA (Active region) 10 Ico BIcao 20 µA 10 μA 1 = 0 με 15 (Cutoff region) 20 VC (V)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A certain npn silicon transistor has vBE=0.7 V for iB=0.1 mA at a temperature of 30°C. Sketch the input characteristic to scale at 30°C. What is the approximate value of vBE for iB = 0.1 mA at 180°C? (Use the rule of thumb that vBE is reduced in magnitude by 2 mV per degree increase in temperature.) Sketch the input characteristic to scale at 180°C.
04:- Design a bias circuit for NPN silicon transistor having a nominal B-100 to be used in voltage divider circuit with Q-point of Ic 10 mA and VCE = 10 V. Use standard valued 5% resistors and draw a schematic diagram of your design. (10 points)
Qa: A transistor dissipates 50W in an ambient temperature of 60°C, the thermal resistances are 0-0.5 °CW¹, 8ca-4 °CW. Determine the junction temperature without a heat sink. Determine the thermal resistance of the heat sink to avoid the junction temperature exceeding 180°C. )
In a BJT, is always the largest and is always lightly doped. a. emitter and collector b. collector and emitter C. collector and base d. emitter and base
Name: (11) The supply voltage VCC equals 9V. The base resistor RB is 42. Take 0.6V for the knee voltage of the base-emitter diode. Draw the load line for a short-circuit current of 15mA (a) What is the value of the collector resistor RC in that case? (b) What is then the voltage Va across the transistor? (c) What is then the current le through the transistor? RB www VCC 9.0V RC Ic (mA) 15 D 10 Student nr. saturation region 5 Answers: (a) RC- (b) Va (c) Ic= active region (12) Same circuit and transistor as above, but now with a short- scircuit current of 5 mA. Draw the new load line. (a) What is the value of the collector resistor RC in that case? (b) What is then the voltage Vc across the transistor? (c) What is then the current Ic through the transistor? cutoff region 10 15 VCE (V) {npn} 20 Answers: (a) RC = (b) VCE= (c) Ic= L₂=0.4 mA 1₁-0.3 mA IB=0.2 mA Ig=0.1mA Ig=0 mA
figure 5 A With the help of the tiand theary only distinguish between an insulator and a semiconductor. b. L Draw a crcult dlagram that can be used to obtain the results shown on the graph in figure 5. IL Use the graph in figure 5 to plox another graph of collector current le agaiat base current Ig. Obtain the current gain for the transistor. III. Explain the tetm thermal runaway. Input Output R Figure 6 The input in figurr 6 is an alternating valtage. Draw the output voltage for the circult.
Draw and explain the schematic diagram for the following: Common Base NPN operating in cut-off region Common Emitter PNP operating in the active region Common Collector NPN operating saturation region From the given figure, identify and explain the 1.Type of Transistor 2. Type of Configuration 3. Mode of Operation V3 SV Q2 100A/A Q3 100A/A 7 V4 5V V6 5V
Transistors originally were made with germanium but modern transistors use silicon for its higher heat tolerance. Transistors amplify and switch signals. They can be analog or digital. Two prevalent transistors today are Metal-Oxide-Semiconductor Field Effect Transistors (MOSFET) and Bipolar Junction Transistors (BJT).In your own understanding in the field of electronics can you compare and contrast which one has merit over the other ?
The maximum drain current for the n-channel enrichment type MOSFET is 30 mA.Determine VGS with this current level if k= 0.06x10-3 A/V2 and VT is the maximum value.
Typically given as IDSS = 10 mA and VGS(off) = -8 V for a JFET. Using these values, determine the drain current for VGS = -2 V.
Design the following MOSFET circuit for it to operate in saturation mode with 0.5 mA drain current. Determine Rp and dc voltage VĎ. Assume V₁ = 2 V and K = 0.1 mA/V² for this MOSFET. 10 V RD -VD
What is the channel in an n-type MOSFET formed of? a. Bound holes b. Mobile holes c. Bound electrons O d. depletion region O e. Mobile electrons