1. A Resistance temperature detector (RTD) is placed in a bridge circuit shown below with a 10kn potentiometer. The RTD has resistance of 40002 at 22°C and a temperature coefficient (ao) of 0.004/°C. When the potentiometer is adjusted to 3.26 kn, the bridge is balanced. Determine the temperature. 9V 1kΩ 2.14ΚΩ 200Ω RTD a) Determine the output voltage from the galvanometer when the temperature at 375k (potentiometer value is 2.78kohm)

1. A Resistance temperature detector (RTD) is placed in a bridge circuit shown below with a 10kn potentiometer. The RTD has resistance of 40002 at 22°C and a temperature coefficient (ao) of 0.004/°C. When the potentiometer is adjusted to 3.26 kn, the bridge is balanced. Determine the temperature. 9V 1kΩ 2.14ΚΩ 200Ω RTD a) Determine the output voltage from the galvanometer when the temperature at 375k (potentiometer value is 2.78kohm)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
A 1 - ∅ full-wave rectifier is made by using thyristors. If the peak value of the sinusoidal input voltage is Vm and the value of the delay angle is 45 degree, find the average value of output voltage Select one: a. 0.65 VM b. 0.85 VM c. 0.45 VM d. 0.25 Vm
For the circuit shown below, the maximum input voltage (Vin max) fin V to turn all the zener diodes in the on state and not to exceed the maximum power rating (PZM) is. 2k lk V2=3v PZM=27mW vz=3V PZM=21mW Vout UTA vz=5V PZH=30mW S1 0 30 O 17 32 021 O 18
To improve the energy efficiency of a synchronous rectifier, (a) A low voltage MOSFET with a very low rɔ5(m) and a high voltage BJT with a very low on-state voltage are used (b) A high voltage MOSFET with a very low rɔs(om) and a low voltage BJT with a very low on-state voltage are used (c) A low voltage MOSFET with a very low rɔs(cm) and a low voltage BJT with a very low on-state voltage are used (d) A high voltage MOSFET with a very low sm) and a high voltage BJT with a very low on-state voltage are used
A certain full-wave rectifier has a peak output voltage of 30 V. A 50 uF capacitor input filter is connected to the rectifier. What is the DC output voltage developed across a 606eohm load resistance?
Determine the DC Voltage for the filtered bridge rectifier with a load as indicated in Figure
The DC value of a full-wave rectified voltage with a peak value of 55 V is a.) in bridge-type b.) in center-tapped
The positive peak value of output waveform for the given circuit diagram is. Bias voltage is 2 V, Diode is germanium) (VPP of input is 18 V, V VouT
At what point on the input cycle does the PIV occur? For a half-wave rectifier, there is current through the load for approximately what percentage of the input cycle?
Question 9 In D-MOSFET, Ipss is the maximum Drain current True False
Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. If we connect a lamp load of 2W across this module, choose the correct statement for the above PV Module. (Assume necessary data) a. The output voltage is 0.5V, the output current is 2A b. The output voltage is 0.5V, the output current is 4A c. The output voltage is 2V, the output current is 2A d. The output voltage is 2V, the output current is 4A
A sinusoidal voltage wave form of peak voltage í V and frequency f = 60Hz is applied to a bridge rectifier and to half wave rectifier separately. The Differences of average values and output frequencies are