1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, mass flow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following: (a) ideal turbine work (b) ideal pump work (c) theoretical thermal efficiency (d) the steam rate (e) heat rate of the cycle (f) actual work of the pump if pump isentropic efficiency is 89% (g) actual turbine work if turbine isentropic efficiency is 90%

Q: solve and show every step with right answer

A: Data given - Rectangular cross section 225×75 mm2 Torsional moment = 20kN Axial Compressive force =…

Q: Find the center (xc, yc) of the given thin plate? Need only handwritten solution only (not typed…

A:

Q: The radial distance measured from the pitch circle of a gear to the top of the gear tooth is known…

A:

Q: The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are…

A:

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: Says.003 is wrong

A:

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: INSTRUCTIONS: Solve for all unknowns (magnitude and direction). A 10' 300# 10' 150# B 5'

A: According to the given data A beam  AB is given  We need to find Reaction  at point A and B

Q: 3. It is desired to design a 5-cylinder aircraft engine with a stroke-bore ratio of 1.2. The piston…

A: here, stroke bore ratio say, l/d ratio = 1.2 so, l = 1.2×d volume per cylinder = π4·d2·l here,…

Q: 2. From the given figure below, solve for the bar Y from the reference line. (choose the nearest…

A:

Q: Input shaft of the gear train shown below rotates at 1,500 RPM. The output shaft must rotate exactly…

A: Given data wA = 1500rpm wB= 500rpm  TA= 20

Q: Complete the orthographic drawing

A: If we plot isometric view, it looks like below

Q: 4. From the given figure, solve for the bar Y from the reference line . (choose the nearest answer)…

A:

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

A:

Q: 2. For the plan area shown, determine the location of the Centriod. Use you're the last two digits…

A:

Q: kindly solve the Ixx and lyy. Enclose and summarize final answers. 100 mm D 50 mm 50 mm 100 mm 60 mm…

A:

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: Two gears are calibrated so that the larger gear drives the smaller gear. The larger gear has a…

A: One complete rotation of the larger gear will make the circumference of the larger gear as the…

Q: 1. If the block is loaded with P = 282 kN, calculate the required dimension "b" of the key.   Write…

A:

Q: The Answer is cut off on the right side.

A:

Q: 0 = 0° A

A:

Q: Q1: Find the angle of the force? 250 Ib 110 Ib 25 140 Ibk 40° 90 Ib 170 Ib

A:

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: 1- Sketch front, right and top views of the following object. Each grid represents 10 mm. Front

A: Given: Sketch Front, top and right side view of the given isometric view.

Q: Question 3) On the  plate in the figure, the length  L  is given as L=72 m . According to this;…

A:

Q: Given : Mass of Gears A and B = 2.4 kgs Mass of Gear C = 12 kgs Gears A and B's radius of gyration =…

A:

Q: Express the quantity 254,998m in mm.

A: To convert meter quantity into millimeter one must be familiar with the no. of mm exist in one…

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: Determine the required mass of block A so that when it is released from rest, it moves the 5 kg…

A:

Q: R.70 B 4x 1.40 There are 4 arched edges with radius 0.70 inches There are 4 arched edges with…

A:

Q: A4B) Force.. represents value of the force. O a. sense O b. magnitude O c. point of application O d.…

A: This question is from classical mechanics.

Q: 3. From the given figure, solve for the bar X from the reference line (choose the nearest answer)

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.