1. A picce of wire 10-in long is tied vertically. The wire has a diameter of 0.1-in and is used to support a load of 100-lb. What is the stress developed within the wire?

Q: A hollow steel tube with an inside diameter of 110 mm must carry a tensile load of 480 kN. Determine…

A:

Q: 1. A steel thick-walled cylinder has an inner diameter of 25mm and an outer diameter 110mm. The…

A:

Q: A small seat angle is used to support a beam with a reaction of 6,000 lbs. Two 1/2 inch diameter…

A:

Q: mum weight of cylinder th your answer in two decimal

A: given:

Q: A hollowed circular clinder carries an axial force of 100 KN. Find the inner diameter if the…

A:

Q: A tank 10 m high and 2 m in diameter is 15 mm thick. The max tangential stress is ? The max…

A: Given data  height = 10 m diameter = 2 m thickness = 15 mm find the maximum tangential stress and…

Q: ng thin walled cylindrical shell, closed at both the ends, is subjected to an internal pressure.…

A: Given:Suppose,The pressure inside the cylinder=PThe thickness of shell= tThe diameter of shell is =d

Q: Consider the circular bent rod with điameter 20 mm. The free-end of the bend is subjected to loads…

A: The horizontal force of 400 Newton will generate a bending moment at the section b-b. The vertical…

Q: a short link in a mechanism carries an axial compressive load of 3500 N. if it has a square cross…

A:

Q: Compute the maximum shear stress (r7maz) that this solid can have. Hint: Problem 3 Use the Mohr's…

A: For solution refer below images.

Q: 3. When two metal sheets are riveted together by a circular rivet, and two forces that are in the…

A:

Q: Problem 1.2. Find the minimum diameter of a steel wire, which is used to raise a load of 4000 N if…

A: Given :- P=4000 N Stress=95 MN/m2 D= diameter of wire in mm

Q: A pipe has an outside diameter of 0.8 inches and inside diameter of 0.19 inches. A force of 105 lbs…

A: Given     Outside diameter, d2 = 0.8 in        Inside diameter, d2 = 0.19 in…

Q: If cross sectional area of a square bar is increased 5 times, keeping same force then tensile stress…

A: If cross sectional area of a square bar is increased 5 times, keeping same force then tensile stress…

Q: c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile…

A:

Q: Module 4 Stress Distribution Point loads of 2000, 4000, and 6000 Ibs act at points A, B and C…

A:

Q: A cylindrical rod .5" in diameter is subjected to an axial load of 11,300 lbs. A square bar of .5"…

A:

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…

A:

Q: 6. Refer to figure 2. Bar АВCD with cross-sectional FIGURE 2 area equal to 600 mm?. Determine the…

A:

Q: A force of 10kN is applied to one end of a 10 inches diameter circular rod. Calculate the stress…

A: According to the given dataP=10kNd=10 in We need to findThe stress developed in the bar

Q: A rod (ABC) diameter at AB is 30 mm and diameter at BC 10 mm is subjected to a tension load of 40…

A:

Q: 1. A 125 x 95 x 10 mm angle is welded to a frame by two 10 mm fillet welds, as shown in Fig. 1. A…

A:

Q: A cylindrical pressure vessel has inner and outer radii 150 mm and 190 mm respectively. If the…

A:

Q: Determine the largest weight “W” that can be supported by the two wires AB and AC. The working…

A:

Q: ADISIDO diameter is 10 times the tube thickness, find the thickness (mm) of the tube.

A: Given   Load, P = 500 kN     Stress = 140 MPa Find   Thickness, t

Q: 1. A cylinder tankhas a maximum load of 2600 kg while the pressure is 2600 kpa. If the ultimate…

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each…

A:

Q: A rectangular block of 1200 mm? cross-section- al area is subjected to a longitudinal compres- sive…

A:

Q: 2. The homogeneous 1000-lb plate is suspended from three cables. Determine the smallest diameter…

A:

Q: Find stress in each segment. Diameter of AB is 2in and diameter of BC is 1in.

A:

Q: 1. A steel rod that is 5.5 feet long, stretches 0.04 inches while under a 2-kip tensile load. a.…

A:

Q: A building weighing 100,000 Ibs is placed on the L-shaped slab shown. The soil below the basement is…

A: We know that, x=A1x1-A2x2A1-A2 A1=80×60=4800 ft2x1=802=40'y1=602=30' A2=50×20=1000…

Q: Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 22 kN if it…

A:

Q: 5 decimal places   Two identical plates of 61 mm wide and 6 mm thick is connected by a square pin…

A: Givenpart 1width w=61mmthickness t=6mmside a=14mmF=29kNpart 2A thin-walled cylinder is subjected to…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.