1. A band-pass filter allows certain frequency bands to pass and can be determined by cut-off frequencies.a. Determine the Fs1, Fp1, Fp2 and Fs2 for the following band-pass filter design inFigure I with sampling frequency of 500Hz, cs1-0.25x. op1-0.35%, cop2=0.55mand cos2-0.65%.Magnitude1+41-46.707Tration BandAmyMwaysPassbandwysFrequencyFigure 1: Band-pass filterTransition BodAyy(=F₂)b. Given the following filter equation, determine the type of the filter.y[n] = 3x[n] + 2x[n- 1] + 3y[n-1]+4x[n-2]+5x[n-4]c. Give two advantages of IIR filter compared to FIR filter.IN

To find: a) Frequencies b)we need to find the type of filter using the given difference equation. c)…

1. A band-pass filter allows certain frequency bands to pass and can be determined by cut- off frequencies. a. Determine the Fsl, Fp1, Fp2 and Fs2 for the following band-pass filter design in Figure I with sampling frequency of 500Hz, cs1-0.25. ap1-0.35%, p2-0.55x and cos2-0.65%. spadry 1+4 1-4 6.707 Trein Bad Siphonal My 32 Pendud Freepany Figure 1: Band-pass filter Tramation Bod Amy - My (=F₂) b. Given the following filter equation, determine the type of the filter. y[n] = 3x[n] + 2x[n- 1] +3y[n-1]+4x[n-2] +5x[n-4] c. Give two advantages of IIR filter compared to FIR filter.

1. A band-pass filter allows certain frequency bands to pass and can be determined by cut- off frequencies. a. Determine the Fsl, Fp1, Fp2 and Fs2 for the following band-pass filter design in Figure I with sampling frequency of 500Hz, cs1-0.25. ap1-0.35%, p2-0.55x and cos2-0.65%. spadry 1+4 1-4 6.707 Trein Bad Siphonal My 32 Pendud Freepany Figure 1: Band-pass filter Tramation Bod Amy - My (=F₂) b. Given the following filter equation, determine the type of the filter. y[n] = 3x[n] + 2x[n- 1] +3y[n-1]+4x[n-2] +5x[n-4] c. Give two advantages of IIR filter compared to FIR filter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. Show how a series RLC filter, its type depends on the output voltage terminal as follows: Low pass filter the output voltage across ... High pass filter the output voltage across . Band pass filter the output voltage across Band reject filter the output voltage across ...... ......... ........
Define briefly the terms used in filter below, a) pass band b) attenuation band c) Cut off frequency (-3db frequency)
1. A band-pass filter allows certain frequency bands to pass and can be determined by cut- off frequencies. a. Determine the Fs1, Fp1, Fp2 and Fs2 for the following band-pass filter design in Figure I with sampling frequency of 500Hz, aos 1-0.25x. op1-0.35%, cp2=0.55m and cos2-0.65%. Magnitude 1+4 1-4 6.707 Tration Band Amy M ways Passband wys Frequency Figure 1: Band-pass filter Transition Bod Ayy (=F₂) b. Given the following filter equation, determine the type of the filter. y[n] = 3x[n] + 2x [n - 1] + 3y[n-1] + 4x[n-2] +5x[n-4] c. Give two advantages of IIR filter compared to FIR filter. IN
Explain why it is necessary to add capacitor in Low pass filter draw circuit diagram and explain w.r.t combination of Capacitor and RL.
Roll off value in frequency response of an active filter is related to A. rate of change of gain B. accuracy of cutoff frequency C. size of swiss roll cake D. number of frequencies rolled in the filter
An FIR bandpass filter is to be designed to meet the following frequency response specifications:and sampling frequency (Fs) is 10 KHzPassband frequencies are: 0.339 - 0.709 (normalizedTransition width: 0.017 (normalized) Stopband deviation: 0.001Passband deviation: 0.05What is the Stopband frequency (fs2) ?
The output power of filter is 100 mW, when the signal frequency is 5 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ?
The mask shown in the figure below belongs to which type of filter : Median filterSharpening frequency filterSharpening spatial filterSmoothing spatial filter
2. a) Consider the circuit shown in figure 3. i) Determine what type of filter is shown in Figure 3 i) Calculate the corner or cutoff frequency. Take R = 4 k &, L= 2 H, and C= 1 uF. R Figure 3 b) Describe the possibility of building a second order filter with only resistors and capacitors? and design the cutoff frequency of second order filter for low pass filter (Expected: Describe the possibility , design the second order filter for low pass filter circuit and design the cutoff frequency as equation only).
(B2) The magnitude characteristic of this filter is equiripple in the passband and monotonic in the stopband.
Determine the transfer function from Uin to Uut! b) Set up amplitude and phase function! c) Assume that we connect 10V (DC) as input voltage at time t-0. How much voltage is then above C2 after a long time?
Calculate the cutoff frequency for the opamp Sallen-Key 2nd order highpass filter