1. A 502 transmission line is connected to a load impedance of 100 + j752. Find the cor- responding: i) reflection coefficient; ii) standing wave ratio; iii) the fraction of the average incident power reflected by the load.

1. A 502 transmission line is connected to a load impedance of 100 + j752. Find the cor- responding: i) reflection coefficient; ii) standing wave ratio; iii) the fraction of the average incident power reflected by the load.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Determine the voltage standing wave ratio VSWR, the reflection coefficient I'and the line return…

Q: A quarter wavelength line is being used to match a load impedance of 80 Ω to a generator with an…

A: Given Quarter wavelength l=λ4Load impedance ZL=80 ΩThe impedance Zin=80 Ω

Q: (b) Define the five of the following: Ampere's Law, Gauss's Law of electric field, Standing wave,…

Q: Which is the result of two identical waves 180 degrees out-of-phase arriving at the receiver at the…

A: Given the question Which is the result of two identical waves 180 degrees out-of-phase arriving at…

Q: A lightning strikes a 30-m unshielded over-head transmission line tower Which has the following…

A: From the given data we have to find the (i) Voltage reflection co-efficents (ii) insulator voltage…

Q: 2. A manufacturer quotes a maximum VSWR of 1.07 for a resistive load when it is used to terminate a…

A: In this answer we will try to find what percentage of the incident power is the reflected power by…

Q: #2-If the magnitude of an incident voltage wave on a load is 18 V and the magnitude of the incident…

Q: A lightning stroke discharges impulse current of 10 kA (peak) on a 400 kV transmission line having…

A: Given values are - Impulse currentI=10kAVt=400kVZS=250ohm Given that equal distribution from point…

Q: i see thes answer, also graph for phase i think wrong, please can you check

A: Given:

Q: Problem-3, Find the characteristic impedance of a quarter wave transformer connected in between a…

A: Given- Quarter wave transformer- Load R2=100 ohm, Transmission line characteristic impedance Zo=225…

Q: 2. The reflection coefficient of a load is L=0.8. Determine: (a) VSWR

A: Given: Reflection coefficient of a load, ΓL=0.8.

Q: A lightning strikes a 30-m unshielded over-head transmission line tower Which has the following…

A: NOTE: "Since you have posted a question with multiple sub parts, we will solve first three sub parts…

Q: A 300 watt carrier is simultaneously modulated by 3 sine waves with modulated percentages of 20, 29…

Q: A transmission line is not properly terminated thereby causing a a reflection coefficient magnitude…

A: In this question we need to find a impedance of the termination.

Q: The voltage between line and ground in a transmission line is the average value of the sine…

A: To solve the above problem, one should know about different voltage measurement in three-phase:…

Q: The characteristic impedance of a transmission line is 70 ohms and has a load of 35 ohms. The SWR…

A: The solution is given below

Q: an overhead line is connected to a terminal apparatus through a length of single phase cable, the…

A: Types of waves Incident wave Reflected wave Refracted wave

Q: Q10) Explain the need for a matching device which using for transmission line, evaluate the…

A: A matching device is needed in a transmission line to ensure that the maximum amount of power is…

Q: 5. If the peak voltage for an AC wave is 100 V, what are its average and rms values? O 100 and…

Q: What is the required bandwidth according to the Carson's rule, when a 100 MHz carrier is modulated…

A: Given information: The frequency of the carrier signal is fc=100 MHz. The modulating frequency is…

Q: If there is no standing wave on a transmission line (constant pattern), then the value of VSWR is: *

A: VSWR: ratio of maximum to minimum voltage for lossless line in terms of voltage…

Q: value of load impedance that absorbes maximum average power.

A: Given circuit is -

Q: What is the required bandwidth according to the Carson's rule, when a 100 MHz carrier is modulated…

A: Given information: The carrier frequency is fc=100 MHz The modulating frequency is fm=1 kHz The…

Q: What is the relation between the PSD and the total average power over 1 ?

A: The objective is to determine the relation for the given condition

Q: Problem 4. A voltage wave of the form V+=(2x 10-4V) cos( -k is incident from cable 1 with…

A: Now calculating the Reflection Coefficient of the medium:We Know:Reflection Coeff.=> Now putting…

Q: For a transmission line w/characteristic impedance Zo = 50 2. At some point of the line, a forward…

A: Given: Characteristics Impedance of transmission line Z0=50 Ohms Forward wave voltage at a point on…

Q: Design a quarter wave matching section if the line has a characteristic impedance of 100 ohm while…

A: Given

Q: If the first and the third reflection coefficients of a matched line are 0.2 and 0.01, then the…

Q: 27. A coil in the radio transmitter has an inductance of 150 milli henry. At what frequency will it…

Q: Explain in detail the reflection and standing wave phenomenon on a transmission line.

A: If the impedance of transmission line i.e. characteristic impedance doesn't matches with the load…

Q: 21. a conductor has a conductance of 70µS is used to supply a load. Find its equivalent resistance…

Q: Q3) Define the return loss of a microwave circuit in terms of the reflection coefficient and the…

A: Given: Return Loss =18 dB Required: (A) The reflection coefficient Γ (B) The…

Q: Method use to determine the phase sequence of the incoming alternator

A: The methods used for the determination of the phase sequence for 2 machines are synchronizing lamps.

Q: A 219-2 lossless air transmission line is connected to a complex load composed of a 579-Nresistor in…

Question

1. A 502 transmission line is connected to a load impedance of 100 + j7592. Find the cor-
responding: i) reflection coefficient; ii) standing wave ratio; ii) the fraction of the average
incident power reflected by the load.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Transmission Line Parameter and Scattering Parameter (S-parameter)

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Derive the expression for the average and rms load voltage for a three phase HWCR operating with an RL type load. ? What will be the average power in the load for the circuit shown, when alpha = π/4 Assume SCR to be ideal. Supply voltage is 330 sin 314t. Also calculate the RMS power .?
What is the required bandwidth according to the Carson's rule, when a 100 MHz carrier is modulated with a sinusoidal signal at 1KHz, the maximum frequency deviation being 50 KHz.
Answer number 14.write youe solution pls.
A lightning strikes a 30-m unshielded over-head transmission line tower Which has the following parameters Surge impedance of the tower= 100ohms Surge impedance of lightning channel at tower top =500ohms Tower-footing resistance=10ohms Tower height =30 m Cross-arm height=27m The lightning strike current is assumed to be a constant 30 kA for a duration of 20 µs. The raveling wave propagation speed in the tower is 1.2* 108 m/s. a) The insulator voltage approaches a constant value after 2 µs. If the basic impulse insulation level (BlL) of the insulator for phase conductor is 150 kV, evaluate the condition of the insulator and conclude the type of power quality problem that will occur for an end-user facility connected to the transmission line. Assume that the surge arrester and circuit breakers at the end-User facility are working properly.
A transmission line of characteristic impedance of Zo=50 ohm with length of A/4 loaded by a load impedance of 150ohm find 1- the load reflection coefficient 2- the standing wave ratio (SWR)
Please help ASAP with a handwritten answer Two identical wave generators in a ripple tank produce an interference pattern using a wavelength of 2.58cm. Point M is on the first nodal line. This point is 12.4 cm from source 1. a) How far is point M from the other source? b) Point N is also on a nodal line. It is 21.8cm from one source and 15.4cm from the other. On Which nodal line is N located? Include a sketch.
A system has a forward power of 60 W, reflected power of 3 W, and transmission line loss of –3 dB. What will be the observed loss on the ground? A system has a forward power of 200 W and a reflected power of 15 W, what is the return loss?
Due to line mismatch, a voltage standing wave ratio of 10 is calculated. The total volatge at the load is 5Vrms. What is the peak amplitude of the incident voltage at the load? Assume that the incident and reflected voltages are in phase at the point of reflection.
This question is about microwave material. I need a solution as soon as possible, please
A single phase line has two parallel conductors 1.5 meter apart. The diameter of each conductor is 1.15cm calculate the inductive and capacitive reactances of the transmission line if it is operating at a frequency of 55Hz.