1) What are the Q-points for the transistors in the amplifier in Figure 2 if V 18 V, V-18 V, Rs 56 kn and Rp= 91 kN? Kp= 200 µA/V² and VTP=-1 V (Şekil 2'de verilen amfideki transistörlerin Q noktası değerlerini bulunuz). b) What are the differential mode gain, common mode gain and CMRR? (Fark, ortak mod kazançlarını ve CMRR değerini bulunuz). Rd Rs Vd1 -O Vd2 -Vs Rd Figure 2. V2

1) What are the Q-points for the transistors in the amplifier in Figure 2 if V 18 V, V-18 V, Rs 56 kn and Rp= 91 kN? Kp= 200 µA/V² and VTP=-1 V (Şekil 2'de verilen amfideki transistörlerin Q noktası değerlerini bulunuz). b) What are the differential mode gain, common mode gain and CMRR? (Fark, ortak mod kazançlarını ve CMRR değerini bulunuz). Rd Rs Vd1 -O Vd2 -Vs Rd Figure 2. V2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a linear amplifier, based on a bipolar junction transistor 2N3904 in common emitter configuration. The supply voltage is 28V. The quiescent operating collector current for the amplifier should be around 10mA. The data sheet for the transistor shows that the DC current gain at this operating current is about 200. Draw the circuit diagram of your design. Label all the components in the circuit. Show all the voltages and currents that you use for calculations in your design. Label them using consistent naming convention.
Draw the DC and AC load line for a transistor amplifier circuit shown in Figure, also describe the optimum operating Point for the given values as follows: Rc = 10 KQ ; RL=20 KQ and V cc = 20 V +Vcc Ic Rc Cc Cc V. out R1 Vin www
Q.) Figure below divider bras amplifier Circuit. Givent the model Parameter : gm = 5o mS emitter (CE) Voltage BJT hibrid- TT Shows a Common riT: 6 Kr and to %3D : 00 +Vc. RI C2 Tooks touf RL Vo ihe 200 RE TCE Vs 20 a Draw the Ac eQuivalent at low Freauency Circuit Zi and b.) Determine inPut impedance at mid FreaUincy OutPut imPedance Z0 c.) Calculafe two low Cut -oFF FreQuen Cies FLC1 and FLC2 Ci and E2 respectively Such as due to the exterda al capacitors
If the amplifier in Figure 4 operates with Rsig= 10 kQ and a load of RL=2kQ. Draw the re model alternating current (ac) equivalent circuit of the amplifier. Determine the input and output impedances. Determine the voltage gain Vo/Vin and Vo/Vsig. Calculate the current gain Io/Ii.
In the self-biased FET amplifier in the figure, Vdd=20V Rs=1kohm Vgsq=-2.6V IDq=2.6mA. It has values of Idss=8mA, Vp=-6V gos=25mikroS. 12mV a.c. to transistor input. What should be the Rd resistance value so that the output voltage is -24.85mV when voltage is applied? answer: 3.3kohm, 3.6kohm, 4.5kohm, 3.9kohm, 4.2kohm is one of the answers.
A transistor amplifier which uses a npn BJT and various passive components is shown in Figure Q2. A table of component values is shown in Table Q2. Calculate the voltage at the collector emitter junction VCE- -- 4 +Vcc R1 Q1 Vout Vin R2 R3 Figure Q2 R1 = R2 = 50 kQ R3 = 5 kQ +Vcc = 15 V Q1: B = 200 VBE(dc) = 0.7 v VT = 25 mV Table of Component values and Transistor Parameters Table Q2 O 8.2V O 0.82V 6.8V 0.68V
Calculate the common-mode gain for the amplifier circuit below. Refer to the image for the circuit configuration, but refer to the following for the values: Vcc = 10 V, Rc = 74674 ohms, RE = 70254 ohms, -Vcc = -11 V, Vi1 = 0 V, ri1=ri2= 29354 ohms, beta1=beta2 = 75.
For the amplifier circuit given in figure below with (Rc = 1.6 k, RE1 = 0.6 k, RE2 = 0.6 %3D k, RF1 = 310 k, RF2 120 k, B=80, and Vcc = 18 v, determine %3D 1. Draw the AC equivelant re model of the amplifier 2. Calculate the input and output impedance 3. Calculate the voltage gain. Re RF, RF2 RE Riz
The circuit shown in the following in figure has: VIN= 10 V, Vz = 7.2 V@ Iz-40 mA, Izk =2 mA, IzM= 100 mA and Zz-5 2. Determine a) Maximum output voltage. b) Minimum output voltage. c) The percentage load regulation. d) The minimum permissible load resistor value. c) The maximum permissible load resistor value. R 2211 VIS
- Compute voltage peak of the input. Is it equal to what you are expecting base from the setvalues of your VAC source? - Compute voltage peak of the output. Is it equal to what you are expecting base from the setvalues of your VAC source?
We examined the common source amplifier shown in the figure in the 5th experiment. The selection criterion of the input capacitance is Xcin = 0.1Rin: Calculate the required input capacitance value, Cin , if an input signal with a frequency of 2 kHz is applied. Şekitde gösterilen ortak source yükseltecini 5. deneyde incelemiştik Giriş kapasitesinin seçim kriteri Xcin - 0.1Rin dir. 2 kHzlik giriç sinyali için gerektt tapasite, Cm değerini hesaplayınız. Circuit parameters / Devre Parametreleri R1 = 53 k2, R, = 17 k2 R1 RD Cout Vout D VDD M2 Cin G Vin R2 RS cs O a. 74.19 nF O b. 86.55 nF O c. 49.46 nF O d. 61.82 nF O e. 43.28 nF
Introducion to Electronic Analysis and Design - CE05 To have a good amplifier Select one: a. The input resistance should be high b. the output resistance should be high c. the voltage gain should be equal to zero d. the current gain should be equal to zero Ssment CE255/EE255 (O1)- Dr. Mamoun Al-Mistar Jump to...