1-The storage tank shown below is to be used to supply a community such that the pressure at Point B is always in the 440 kPa. The water-demand of the community is expected to 1m3/s. The bottom of the storage tank is 42 m above ground level, and the supply pipe is 1.5 m below ground level. The length of pipe(Point A) and Point B is 1 km, the diameter of the pipe is 600 mm, and the pipe contains five 90° bends(k= 0.8). An auxiliary pumping system will ensure that the tank never becomes empty. a)Determine the water depth (h) in the tank that will meet the design pressure requirements at B. 42 m VE TEMETWEETEAMETHE THE METEME METE Supply pipe 1.5 Storage tank m B P1+1 28 : +²₁) = Z1 Flow P2 Y +02 + 22 +hi+hs

1-The storage tank shown below is to be used to supply a community such that the pressure at Point B is always in the 440 kPa. The water-demand of the community is expected to 1m3/s. The bottom of the storage tank is 42 m above ground level, and the supply pipe is 1.5 m below ground level. The length of pipe(Point A) and Point B is 1 km, the diameter of the pipe is 600 mm, and the pipe contains five 90° bends(k= 0.8). An auxiliary pumping system will ensure that the tank never becomes empty. a)Determine the water depth (h) in the tank that will meet the design pressure requirements at B. 42 m VE TEMETWEETEAMETHE THE METEME METE Supply pipe 1.5 Storage tank m B P1+1 28 : +²₁) = Z1 Flow P2 Y +02 + 22 +hi+hs

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 150-mm pipeline shown below conducts water from the reservoir and discharges at a lower elevation through a nozzle with a discharge diameter of 50 mm. The water surface in reservoir 1 is at an elevation of 30 m, the pipe intake 2 and 3 at an elevation of 25 m, and the nozzle 4 and 5 at elevation 0. The head losses are: from 1 to 2, 0; from 2 to 3, 0.6 m; from 3 to 4, 9 m; from 4 to 5, 3 m. Compute the pressure head at point 4 in m.
5 Two reservoirs are connected by a pipeline, The diameter of the pipe is (0.5 m and the difference in levels of the two reservoirs is 12.5 m. The total length of the pipe is 1000 m. The velocity of flow in the pipe taking into account both major and minor losses will be [Take, friction factor f-0.04 and g 10 m/sec] (a) 1.75 m/s (c) 4.5 m/s (b) 3.2 m/s (d) 0.5 m/s
Reservoirs A and B with water levels at 72 m and 57 m respectively above datum are connected to a junction J located at 43 m above datum. A third pipeline connects a third reservoir with the junction. The pipeline parameters are as follows. Pipe reach Diameter (mm) 400 Length (m) The friction factor for all the pipes may be assumed as f = 0.02. If a pressure gauge at the junction reads 90 kN/m², determine the distribution of discharges in the three pipes and also the water surface elevation in the reservoir C. Neglect local losses. A AJ BJ CJ 800 600 1000 750 850 C +72.00 400 mm 1000 m H, = +43.00 850 m 300 mm 750 m 600 mm B +57.00 Pressure head +elevation head
A pitot-static tube placed in the centre of a 300 mm pipe line has one orifice point- ing upstream and other perpendicular to it. The mean velocity in the pipe is 0.80 of the central velocity. Find the discharge through the pipe if the pressure difference between the two orifices is 60 mm of water. Take the co-efficient of pitot tube as C = 0.98.
Two tanks A and B have 80 m diffenence in water levels, and are connected by a pipe 0.3 m diameter and 8 km long with 0.002 friction coefficient. The pipe is tapped at its mid point to leak out 35 1/s flow rate. Determine the leaving tank А? discharge Find the discharge entering tank B? Coefficient (Tank Exit) = 0.5 %3D Coefficient (Tank Entry) = 1 %3D ha %3D A he 80 m Q1
Situation 3: Three reservoirs A, B and C are connected respectively with pipes 1, 2 and 3 joining at a common junction P. Reservoir A is at elevation 80m, reservoir B at 70m and C is at 60m. Assume f=0.018 for all pipes. Pipe 1: L-5000 m, D = 300 mm Pipe 2: L= 4000 m, D = 250 mm Pipe 3: L=3500 m EL 80m A EL 70m Qı=0.045 CMS Q2 El. 60m 12. Determine the flow in pipe 2. 13. Determine the flow in pipe 3. 14. Determine the diameter of pipe 3.
SITUATION 2: Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common junction P. Reservoir A is at elevation 80 m, reservoir B at elevation 70 m and reservoir C is at elevation 60 m. The properties of each pipe are as follows: Elev 80 ha hez Elev 70 B 4000 m- 250 mm f-0.018 he 3500 m f- 0.018 Elev 60 Pipe 1: L= 5000 m, D = 300 mm Pipe 2: L= 4000 m, D = 250 mm Pipe 3: L= 3500 m 5000 m - 300 mm f= 0.018
1. Two tanks A and B have 70 m difference in water levels, and are connected by a pipe 0.25 m diameter and 6 km long with 0.002 friction coefficient. The pipe is tapped at its mid point to leak out 0.04 m3/s flow rate. Minor losses are ignored. (a) Determine the discharge leaving tank A? (b) Find the discharge entering tank B? ha А he B Q3 h = 70 m
A new steel pipe (f= 0.02) of 7000m length and 600mm diameter connects two reservoirs as shown. Including all losses, design the water level elevation in reservoir A such that the required flow rate of 0.5m³/s is achieved. Draw the EGL and HGL. %3D ma eyad Tarawneh z= ??? AMSL A z = 650 AMSL В V
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. Include minor losses. (DO NOT ROUND OFF)
In the branched pipe system shown, 850 L/min of water at 10°C is flowing in a DN 100 Schedule 40 pipe at A. The flow splits into two DN 50 Schedule 40 pipes as shown and then rejoins at B. Calculate (a) the flow rate in each of the branches and (b) the pres- sure difference PA PB. Include the effect of the minor losses in the lower branch of the system. The total length of pipe in the lower branch is 60 m. The elbows are standard.
1] A pump draws water from an open reservoir, with a static suction headof 26.24 feet, and lifts it to another open reservoir with a static discharge head of25 meters. The diameter of the suction pipe is 15.24 cm and the diameter ofdischarge pipe is 4.0 inches. The total head loss from A to B is 25 % of the totaldynamic head (TDH), and the head loss at the discharge side of the pump is 90 %of the total head loss. The pump capacity is 50 lps. Determine: a) the pump brakepower if the efficiency is 82 %; b) the reading of the pressure gauge installed atthe suction side of the pump; and c) the reading of the pressure gauge installed atthe discharge side of the pump.